lanane
2015-09-21, 13:38
O.K. I'm not a Linux pro but this is a fairly simple command.
One thing I will note : This is a clean install, I screwed my other install up trying to get ... Not Cuda but the OS version of it going. Anyways. Here it is :
root@Kali:~# airmon-ng stop wlan0
PHY Interface Driver Chipset
phy0 wlan0 rtl8188ee Realtek Semiconductor Co., Ltd. RTL8188EE Wireless Network Adapter (rev 01)
You are trying to stop a device that isn't in monitor mode.
Doing so is a terrible idea, if you really want to do it then you
need to type 'iw wlan0 del' yourself since it is a terrible idea.
Most likely you want to remove an interface called wlan[0-9]mon
If you feel you have reached this warning in error,
please report it.
root@Kali:~#
Same thing happens on my Wlan1 which has injection capabilities. Althought I never had problems putting wlan0 in monitor mode.
I can override it but then in iwconfig it shows a weird monitor .. Something like mon0monmon ... And it doesn't work when I try to capture handshakes
P.S. I did do ....
apt-get clean
apt-get update
apt-get upgrade
apt-get dist-upgrade
Also prior to running Airmon, below was status :
root@Kali:~# iwconfig
eth0 no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:"ATT"
Mode:Managed Frequency:2.427 GHz Access Point: 22: 56: 22: 9E: A0: 22
Bit Rate=72.2 Mb/s Tx-Power=20 dBm
Retry short limit:7 RTS thr=2347 B Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=70/70 Signal level=-38 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:158 Missed beacon:0
lo no wireless extensions.
wlan1 IEEE 802.11bgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
P.S. Code command would be nice on main page. I looked for it, but didn't know I had to go advanced
One thing I will note : This is a clean install, I screwed my other install up trying to get ... Not Cuda but the OS version of it going. Anyways. Here it is :
root@Kali:~# airmon-ng stop wlan0
PHY Interface Driver Chipset
phy0 wlan0 rtl8188ee Realtek Semiconductor Co., Ltd. RTL8188EE Wireless Network Adapter (rev 01)
You are trying to stop a device that isn't in monitor mode.
Doing so is a terrible idea, if you really want to do it then you
need to type 'iw wlan0 del' yourself since it is a terrible idea.
Most likely you want to remove an interface called wlan[0-9]mon
If you feel you have reached this warning in error,
please report it.
root@Kali:~#
Same thing happens on my Wlan1 which has injection capabilities. Althought I never had problems putting wlan0 in monitor mode.
I can override it but then in iwconfig it shows a weird monitor .. Something like mon0monmon ... And it doesn't work when I try to capture handshakes
P.S. I did do ....
apt-get clean
apt-get update
apt-get upgrade
apt-get dist-upgrade
Also prior to running Airmon, below was status :
root@Kali:~# iwconfig
eth0 no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:"ATT"
Mode:Managed Frequency:2.427 GHz Access Point: 22: 56: 22: 9E: A0: 22
Bit Rate=72.2 Mb/s Tx-Power=20 dBm
Retry short limit:7 RTS thr=2347 B Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=70/70 Signal level=-38 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:158 Missed beacon:0
lo no wireless extensions.
wlan1 IEEE 802.11bgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm
Retry short limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
P.S. Code command would be nice on main page. I looked for it, but didn't know I had to go advanced