View Full Version : Rssi = 00
Dedossss
2016-03-02, 22:52
When i use the Wash command the RSSI = 00 on all the networks that i can find......In the videos i have watched on WIFI Hacking the RSSI values are all different depending on the strength of the signal.....So i am guessing this is why i am not having any luck so far cracking any AP's
Does anyone have a solution for this problem......I have searched for an answer here but had no luck finding one......or if one is posted here.....if you can post the link to the thread.....it would be greatly appreciated......
Thanks.....
Gh0sT.sh
2016-03-03, 06:57
apt-get install libpcap-dev
apt-get isntall libsqlite3-dev
Then, you should download the reaver itself. You can do that from official site.
wget http://reaver-wps.googlecode.com/files/reaver-1.4.tar.gz
Unpack tar :
tar -xvzf reaver-1.4.tar.gz
Go to unpacked dir
cd reaver-1.4/src/
./configure
make
sudo make install
Then remove an existing wash
sudo rm /usr/bin/wash
copy wash from src direcory to /usr/bin/
cp wash /usr/bin/wash
Now try wash
wash -i mon0
and it should work. =)
Dedossss
2016-03-03, 13:06
Thank you for the info.......I will give it a shot....
i was thinking about buying a grid myself. how do you find it? can you give me some hints/best assestments/how does it work. i'm having some doubts and didn't found any good examples how to best drain it's powers :)
Dedossss
2016-03-04, 01:37
If you are referring to my antenna i bought it to use with my DD-WRT flashed router......For testing with Kali-Linux i am going to buy a Yagi directional antenna to use.....I read somewhere that a directional antenna was better for locking in on a single AP.....
Dedossss
2016-03-04, 04:05
I followed the directions above but there was no change......Still have the same problem.......
SKSvensson
2016-03-05, 00:23
I found a Kali bug report that describes this problem as being in the Atheros chipset drivers. Unfortunately there isn't an update on when/if this will be fixed.
https://bugs.kali.org/view.php?id=1288
Dedossss
2016-03-08, 23:05
Apparently that is true......I was using the alfa awus036nha model which was giving me the problem.....So i tried an alfa awus036h and it worked fine.....
So i thought maybe i had a defective one so i tried another new one and had the same issue....
Someone should edit this post.....
https://forums.kali.org/showthread.php?19387-802-11-Recommended-Wireless-Cards
and remove that model from the list.....I bought that model because it was recommended there.....I hope they can fix the problem......
aanarchyy
2016-03-08, 23:47
Apparently that is true......I was using the alfa awus036nha model which was giving me the problem.....So i tried an alfa awus036h and it worked fine.....
So i thought maybe i had a defective one so i tried another new one and had the same issue....
Someone should edit this post.....
https://forums.kali.org/showthread.php?19387-802-11-Recommended-Wireless-Cards
and remove that model from the list.....I bought that model because it was recommended there.....I hope they can fix the problem......
It's a problem with wash(and the whole reaver project to be honest...), not with the card.
And you can prove it to yourself just by running airodump-ng and seeing all the signal strengths reported just fine.
If you're looking for WPS data, just run airodump-ng --wps
Dedossss
2016-03-09, 22:56
Will check that out......Thanks.....