Alfa AWUS036NH not usable when i connect it

[enshem]

Hello guys i installed the latest version of Kali Linux 32bit (2018.1) on USB persistence
i run it mostly with my laptop
and i have Alfa AWUS036NH wireless card and its not appear when i use the command
its detect only the chipset of my laptop the builtin wireless card
airmon-ng i see

PHY Interface Driver Chipset

phy0 wlan0 ath9k Qualcomm Atheros QCA9565 / AR9565 Wireless Network Adapter (rev 01)

any chance that i can do something about it?
i cant find driver for it i did some research and its said that this card no need driver for Linux and should work without any problem
maybe because i use in laptop it do not recognize it?
when i used it on VMware back then it worked great

ifconfig :

eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet 10.0.0.8 netmask 255.255.255.0 broadcast 10.0.0.255
inet6 fe80::9cb5:132f:6d16:4916 prefixlen 64 scopeid 0x20<link>
ether 18:31:bf:71:39:f5 txqueuelen 1000 (Ethernet)
RX packets 32981 bytes 43967718 (41.9 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 20741 bytes 1677612 (1.5 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1000 (Local Loopback)
RX packets 27 bytes 1389 (1.3 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 27 bytes 1389 (1.3 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

[Mister_X]

lsusb should indicate whether is it plugged or not. Look also in dmesg to see if there is any error about it. Clear dmesg before plugging the card using "dmesg -c" to have only relevant info.

[enshem]

lsusb should indicate whether is it plugged or not. Look also in dmesg to see if there is any error about it. Clear dmesg before plugging the card using "dmesg -c" to have only relevant info.

even when i plug and use dmesg and when i unplug its same


[ 245.439917] usb 1-4.1: USB disconnect, device number 10
[ 254.880094] usb 1-4.1: new full-speed USB device number 11 using xhci_hcd
[ 255.170580] usb 1-4.1: New USB device found, idVendor=0951, idProduct=16a4
[ 255.170594] usb 1-4.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 255.170601] usb 1-4.1: Product: HyperX 7.1 Audio
[ 255.170608] usb 1-4.1: Manufacturer: Kingston
[ 255.170614] usb 1-4.1: SerialNumber: 00000000
[ 255.322279] input: Kingston HyperX 7.1 Audio as /devices/pci0000:00/0000:00:14.0/usb1/1-4/1-4.1/1-4.1:1.3/0003:0951:16A4.0009/input/input25
[ 255.380516] hid-generic 0003:0951:16A4.0009: input,hiddev1,hidraw5: USB HID v1.11 Device [Kingston HyperX 7.1 Audio] on usb-0000:00:14.0-4.1/input3