Results 1 to 3 of 3

Thread: Reaver/Bully problem. Kali problem? backports problems?

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Join Date
    2017-Mar
    Location
    Usa
    Posts
    4

    Reaver/Bully problem. Kali problem? backports problems?

    Hello. I am very familiar with WiFi pen-testing over the last 12 months, and I've tried a large amount of routers with a wide range of techniques, however, I found a problem and I am addressing it to Kali.

    Regard the above, I would like to hear from you some to see if someone found and could resolve this problem. I would like to put a background here, since this would be helpful to understand that I am actually doing it right.

    Normally, in my first steps of WiFi pen-testing my first approach is to try Reaver at first (when WPS enabled, of course).

    Wherever, whenever the AP is WPS enable I try commands as follow:

    reaver -i wlan0mon -b xx:xx:xx:xx:xx -e essid name (sometimes I overpass this, since both scripts works fine without -e) -N -D -S -vv (if sensible router is found, such as belkin, broadcom, ralink, I use the proper commands to de-cloak the PIN without brute-forcing the whole 11000 set). Sometimes I would require to deactivate -S because no small DH packets can be processed in order to associate (especially the older ones).

    or

    bully -b xx:xx:xx:xx:xx -N -F -C -v3 wlan0mon (with -d if pixiedust version is used).

    Many times this has worked wonderful, except to new routers that would come with WPS locks (some routers last 5 minutes, other last even 48 hours).

    Of course, if I can, I test the mdk3 command to see if I can overload the router a force a hard reset (I tried the musket team version which includes the -t command) so far so good, no a single router with AP lock I could found vulnerable to this attack. However this is not the point, yet.

    In some cases, some pesky and wayward routers may require a fakeauth from aireplay-ng which I combine:

    reaver -i wlan0mon -b xx:xx:xx:xx:xx -e essid name (sometimes I overpass this, since both scripts works fine without -e) -A -N -D -S -vv (note the "A"). Or at least an A in these commands.

    aireplay-ng -1 30 (may vary between 3 to 60, depending on the stability on the router) -q 3 (sending keep alive packets is quite good to avoid connections failures, at least to me) -a xx:xx:xx:xx:xx wlan0mon

    This way is quite slow, but it works (between 8 to 40 seconds to associate with a average of 9 to 14 seconds in these pesky routers).

    However, and here's where comes the intriguing problem I have met with 2 routers, 1 d-link and 1 tp-link.

    Both were susceptible to the PIN bruteforce (wash -i wlan-mon -C, etc) with no AP WPS rate lock, and I could try almost 3k (d-link) and 5k (tp-link) PINs using bully (<standard> procedure) with -49 dbi (d-link) -60dbi (tp-link).

    Suddenly, both routers start to give me Timeouts everywhere (bully, reaver, reaver+aireplay) with no reason, not a single M1 NACK is given. Little bit frustrating. However this is good for the owners.


    I have tried other router that I already know the tool works, but this is not happening with every router. Just these 2.

    My idea that is related with Kali is that the problem started almost in the same date I decided to make a backport upgrate (just because why not? I have not seen any problem with users before).

    For technical information:

    Gnome Version 3.22.2
    GNU bash, version 4.4.11(1)-release (x86_64-pc-linux-gnu)
    Kernel base upgraded https://www.kernel.org/pub/linux/ker...stable/v4.4.2/
    Also, every apt-get update, apt-get upgrade, apt-get distr-upgrade was done.
    apt-get autoremove also was done.

    I dunno. What do you guys think about this problem?

    Any idea? should I apply a backport downgrade from the beginning?

  2. #2
    Join Date
    2016-Dec
    Posts
    806
    What do you mean by making a backport update?

    Do you mean you install latest linux-backports? If yes, then you downgraded your wireless drivers.

  3. #3
    Join Date
    2017-Mar
    Location
    Usa
    Posts
    4
    To mister_x.
    Yes I did a backport upgrade, to the latest stable version.

    I tried downgrading the bacports to the version it comes with Kali.

    However, the problem it does not disappear.

    Has someone found this problem before? Which technique you guys used?

    Also, I'm trying with some pauses, however it doesn't​ matter, either.

Similar Threads

  1. Are Bully / Reaver broken, or has WPS been fixed?
    By tyson0317 in forum TroubleShooting Archive
    Replies: 0
    Last Post: 2021-01-14, 06:44
  2. Replies: 0
    Last Post: 2017-03-26, 22:38

Tags for this Thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •