Ralink Technology, Corp. RT5370 Wireless Adapter not functioning

Hi, I'm not sure if this the right area for this, so sorry in advance if it isn't :)

I have a Raspberry PI and I originally installed PwnPi on it and I was successfully able to set my RT5370 dongle to monitor mode, but now when I installed Kali, iwconfig shows that wlan0 has no wireless extensions

Heres ifconfig:

Code:

---

eth0      Link encap:Ethernet  HWaddr b8:27:eb:fe:26:d8
          inet addr:192.168.1.19  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::ba27:ebff:fefe:26d8/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:461461 errors:0 dropped:4206 overruns:0 frame:0
          TX packets:100697 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:618335610 (589.6 MiB)  TX bytes:9248830 (8.8 MiB)

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wlan0    Link encap:Ethernet  HWaddr 00:87:31:53:13:e4
          inet addr:192.168.1.10  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST  MTU:1500  Metric:1
          RX packets:10 errors:0 dropped:0 overruns:0 frame:0
          TX packets:11 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:1559 (1.5 KiB)  TX bytes:1793 (1.7 KiB)

---

Heres lsusb:

Code:

---

Bus 001 Device 002: ID 0424:9512 Standard Microsystems Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 003: ID 0424:ec00 Standard Microsystems Corp.
Bus 001 Device 004: ID 148f:5370 Ralink Technology, Corp. RT5370 Wireless Adapter

---

And here is my lsmod, I installed the ralink-firmware using apt-get install

Code:

---

Module                  Size  Used by
aes_generic            34148  0
ipv6                  207600  10
arc4                    1312  2
rt2800usb              11093  0
rt2800lib              44084  1 rt2800usb
crc_ccitt                940  1 rt2800lib
rt2x00usb              6228  1 rt2800usb
rt2x00lib              26852  3 rt2x00usb,rt2800lib,rt2800usb
mac80211              211324  3 rt2x00lib,rt2x00usb,rt2800lib
cfg80211              112728  2 mac80211,rt2x00lib
leds_gpio              1668  0
led_class              1788  2 leds_gpio,rt2x00lib

---

Dmesg | tail:

Code:

---

wlan0: associate with 70:54:d2:98:ec:c4 (try 1/3)
wlan0: RX AssocResp from 70:54:d2:98:ec:c4 (capab=0x431 status=0 aid=2)
IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
wlan0: associated
wlan0: deauthenticating from 70:54:d2:98:ec:c4 by local choice (reason=3)
cfg80211: Calling CRDA to update world regulatory domain
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
smsc95xx 1-1.1:1.0: eth0: kevent 2 may have been dropped
smsc95xx 1-1.1:1.0: eth0: kevent 2 may have been dropped
IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready

---

I cant set it to monitor using ifconfig or airmon-ng, and in PwnPi it showed up correctly, but in Kali it shows Link encap: Ethernet?

I'm sort of new with the Pi and Kali-stuff, so I can't figure out why it's not working on this distro, I've run apt-get upgrade and upgrade-distro
But I still cant get it to monitor mode.

Any help would be greatly appreciated :D

EDIT: I actually got it working, turns out iwconfig is deprecated and you should use iw in Kali, I followed instructions in here to get everything set up and working.
http://wireless.kernel.org/en/users/Documentation/iw

I don't know if this thread should be deleted in case anyone else has the same problems.