No network in Network Manager, Cant connect to wifi. But airodump-ng working

2 Attachment(s)

I've just started kali for a month and just know all the basics. I have dual booted kali with windows using USB.

I can search for networks using airodump-ng.But I cant connect to any of the network.

Here are some commands:

iwconfig
wlan0 IEEE 802.11 ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm
Retry short limit:7 RTS thr=2347 B Fragment thr:off
Encryption key:off
Power Management:off

lo no wireless extensions.

eth0 no wireless extensions.

ifconfig
eth0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
inet 192.168.0.1 netmask 255.255.255.0 broadcast 192.168.0.255
ether 54:e1:ad:1b:d4:ab txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1 (Local Loopback)
RX packets 56 bytes 3904 (3.8 KiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 56 bytes 3904 (3.8 KiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

wlan0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether fe:61:ad:65:48:99 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

lspci
00:00.0 Host bridge: Intel Corporation Device 5910 (rev 05)
00:01.0 PCI bridge: Intel Corporation Skylake PCIe Controller (x16) (rev 05)
00:02.0 VGA compatible controller: Intel Corporation Device 591b (rev 04)
00:14.0 USB controller: Intel Corporation Sunrise Point-H USB 3.0 xHCI Controller (rev 31)
00:14.2 Signal processing controller: Intel Corporation Sunrise Point-H Thermal subsystem (rev 31)
00:16.0 Communication controller: Intel Corporation Sunrise Point-H CSME HECI #1 (rev 31)
00:17.0 RAID bus controller: Intel Corporation 82801 Mobile SATA Controller [RAID mode] (rev 31)
00:1c.0 PCI bridge: Intel Corporation Sunrise Point-H PCI Express Root Port #2 (rev f1)
00:1c.2 PCI bridge: Intel Corporation Sunrise Point-H PCI Express Root Port #3 (rev f1)
00:1c.3 PCI bridge: Intel Corporation Sunrise Point-H PCI Express Root Port #4 (rev f1)
00:1f.0 ISA bridge: Intel Corporation Sunrise Point-H LPC Controller (rev 31)
00:1f.2 Memory controller: Intel Corporation Sunrise Point-H PMC (rev 31)
00:1f.3 Audio device: Intel Corporation Device a171 (rev 31)
00:1f.4 SMBus: Intel Corporation Sunrise Point-H SMBus (rev 31)
01:00.0 3D controller: NVIDIA Corporation Device 1c8d (rev a1)
02:00.0 SD Host controller: O2 Micro, Inc. SD/MMC Card Reader Controller (rev 01)
03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8821AE 802.11ac PCIe Wireless Network Adapter
04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 10)

lsusb
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 002: ID 174f:2414 Syntek
Bus 001 Device 004: ID 18f8:0f97
Bus 001 Device 003: ID 0bda:0821 Realtek Semiconductor Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub

Attached below is the photo of the network manager.
Hopefully there is a fix to this problem.

Show the output of rfkill list all

it was
0: ideapad_wlan: Wireless Lan
Soft Blocked: no
Hard Blocked: yes
1: ideapad_bluetooth: Bluetooth
Soft Blocked: no
Hard Blocked: yes
2: hci0: Bluetooth
Soft Blocked: no
Hard Blocked: no
3: phy0: Wireless LAN
Soft Blocked: no
Hard Blocked: no

but i followed other thread's solution and blocked ideapad

so now is left with

0: hci0: Bluetooth
Soft Blocked: no
Hard Blocked: no
1: phy0: Wireless LAN
Soft Blocked: no
Hard Blocked: no

and there is no wifi switch on my laptop
im using lenovo y520

Can you provide a link to that thread where you got that solution? Though you have successfully blacklisted the ideapad_wlan driver yet i still want to see the output of lsmod and cat /etc/modrobe.d/blacklist.conf.

i seem to forget the link,

lsmod
Module Size Used by
fuse 98304 3
nfnetlink_queue 24576 0
nfnetlink_log 20480 0
nfnetlink 16384 2 nfnetlink_log,nfnetlink_queue
binfmt_misc 20480 1
nls_ascii 16384 1
nls_cp437 20480 1
vfat 20480 1
fat 69632 1 vfat
snd_hda_codec_hdmi 49152 1
snd_hda_codec_realtek 90112 1
snd_hda_codec_generic 69632 1 snd_hda_codec_realtek
uvcvideo 90112 0
videobuf2_vmalloc 16384 1 uvcvideo
videobuf2_memops 16384 1 videobuf2_vmalloc
videobuf2_v4l2 24576 1 uvcvideo
videobuf2_core 36864 2 uvcvideo,videobuf2_v4l2
arc4 16384 2
rtl8821ae 225280 0
btcoexist 53248 1 rtl8821ae
intel_rapl 20480 0
rtl_pci 28672 1 rtl8821ae
x86_pkg_temp_thermal 16384 0
videodev 176128 3 uvcvideo,videobuf2_core,videobuf2_v4l2
intel_powerclamp 16384 0
rtlwifi 77824 2 rtl_pci,rtl8821ae
coretemp 16384 0
mac80211 671744 3 rtl_pci,rtlwifi,rtl8821ae
kvm 589824 0
cfg80211 589824 2 mac80211,rtlwifi
media 40960 2 uvcvideo,videodev
i915 1236992 15
irqbypass 16384 1 kvm
nouveau 1544192 0
joydev 20480 0
evdev 24576 15
serio_raw 16384 0
pcspkr 16384 0
mxm_wmi 16384 1 nouveau
btusb 45056 0
btrtl 16384 1 btusb
ttm 98304 1 nouveau
efi_pstore 16384 0
iTCO_wdt 16384 0
iTCO_vendor_support 16384 1 iTCO_wdt
efivars 20480 1 efi_pstore
sg 32768 0
drm_kms_helper 155648 2 nouveau,i915
hci_uart 98304 0
btbcm 16384 2 hci_uart,btusb
btqca 16384 1 hci_uart
ac 16384 0
acpi_pad 24576 0
btintel 16384 2 hci_uart,btusb
battery 16384 0
intel_lpss_acpi 16384 0
intel_lpss 16384 1 intel_lpss_acpi
bluetooth 552960 7 btrtl,hci_uart,btintel,btqca,btbcm,btusb
tpm_crb 16384 0
tpm_tis 16384 0
tpm_tis_core 20480 1 tpm_tis
tpm 45056 3 tpm_tis,tpm_crb,tpm_tis_core
wmi 16384 2 mxm_wmi,nouveau
rfkill 24576 4 bluetooth,cfg80211
drm 360448 10 nouveau,i915,ttm,drm_kms_helper
video 40960 2 nouveau,i915
mfd_core 16384 1 intel_lpss
i2c_algo_bit 16384 2 nouveau,i915
mei_me 36864 0
mei 102400 1 mei_me
snd_hda_intel 36864 6
shpchp 36864 0
snd_hda_codec 135168 4 snd_hda_intel,snd_hda_codec_hdmi,snd_hda_codec_gen eric,snd_hda_codec_realtek
button 16384 2 nouveau,i915
snd_hda_core 81920 5 snd_hda_intel,snd_hda_codec,snd_hda_codec_hdmi,snd _hda_codec_generic,snd_hda_codec_realtek
snd_hwdep 16384 1 snd_hda_codec
snd_pcm 110592 4 snd_hda_intel,snd_hda_codec,snd_hda_core,snd_hda_c odec_hdmi
snd_timer 32768 1 snd_pcm
snd 86016 20 snd_hda_intel,snd_hwdep,snd_hda_codec,snd_timer,sn d_hda_codec_hdmi,snd_hda_codec_generic,snd_hda_cod ec_realtek,snd_pcm
soundcore 16384 1 snd
efivarfs 16384 1
ip_tables 24576 0
x_tables 36864 1 ip_tables
autofs4 40960 2
ext4 585728 1
crc16 16384 2 bluetooth,ext4
jbd2 106496 1 ext4
crc32c_generic 16384 0
fscrypto 28672 1 ext4
ecb 16384 0
mbcache 16384 2 ext4
sd_mod 45056 4
hid_generic 16384 0
usbhid 53248 0
crct10dif_pclmul 16384 0
crc32_pclmul 16384 0
crc32c_intel 24576 2
ghash_clmulni_intel 16384 0
aesni_intel 167936 0
aes_x86_64 20480 1 aesni_intel
lrw 16384 1 aesni_intel
gf128mul 16384 1 lrw
glue_helper 16384 1 aesni_intel
ablk_helper 16384 1 aesni_intel
cryptd 24576 3 ablk_helper,ghash_clmulni_intel,aesni_intel
psmouse 135168 0
i2c_i801 24576 0
i2c_smbus 16384 1 i2c_i801
ahci 36864 3
libahci 32768 1 ahci
sdhci_pci 28672 0
xhci_pci 16384 0
r8169 81920 0
sdhci 45056 1 sdhci_pci
mii 16384 1 r8169
xhci_hcd 188416 1 xhci_pci
libata 249856 2 ahci,libahci
mmc_core 147456 2 sdhci,sdhci_pci
scsi_mod 225280 3 sd_mod,libata,sg
usbcore 249856 5 uvcvideo,usbhid,xhci_pci,btusb,xhci_hcd
usb_common 16384 1 usbcore
i2c_hid 20480 0
hid 122880 3 i2c_hid,hid_generic,usbhid

and then the cat /etc/modprobe.d/blacklist.conf.

blacklist ideapad-laptop

and I have additional info for my kali version

lsb_release -a
No LSB modules are available.
Distributor ID: Kali
Description: Kali GNU/Linux Rolling
Release: kali-rolling
Codename: kali-rolling

uname -a
Linux Kali 4.9.0-kali3-amd64 #1 SMP Debian 4.9.18-1kali1 (2017-04-04) x86_64 GNU/Linux

Show the output of modinfo rtl8821ae | head

her is the output of modinfo rtl8821ae | head

btw thanks for looking into my problem

filename: /lib/modules/4.9.0-kali3-amd64/kernel/drivers/net/wireless/realtek/rtlwifi/rtl8821ae/rtl8821ae.ko
firmware: rtlwifi/rtl8821aefw.bin
description: Realtek 8821ae 802.11ac PCI wireless
license: GPL
author: Realtek WlanFAE <[email protected]>
alias: pci:v000010ECd00008821sv*sd*bc*sc*i*
alias: pci:v000010ECd00008812sv*sd*bc*sc*i*
depends: rtlwifi,rtl_pci,btcoexist,mac80211
intree: Y
vermagic: 4.9.0-kali3-amd64 SMP mod_unload modversions

I get a simialr problem with my rtl8812au card when i use kismet, or similar programs. I think the issue is that kismet puts the card into monitor mode and gets stuck there ...if I close kismet then remove the card and reinsert it (or rmmod rtl88xxau, then modprobe it again) it starts working. Just a thought?
Good luck.

Quote:

Originally Posted by ptpi

I get a simialr problem with my rtl8812au card when i use kismet, or similar programs. I think the issue is that kismet puts the card into monitor mode and gets stuck there ...if I close kismet then remove the card and reinsert it (or rmmod rtl88xxau, then modprobe it again) it starts working. Just a thought?
Good luck.

Can you give me a step by step guide :) I'm still quite new to this :( Thanks mate

I was not able to find the conflicting driver but rtl8821ae can be one. It may be a legitimate driver of your wifi adapter but still give a try and blacklist it.

so i just add blacklist rtl8821ae in the blacklist.conf?

I don't know if it will work, but...
if it's a usb device, unplug it; wait a few seconds, then plug it in again. DONT run airodump; just go straight to networkmanager. See if it works. (But this will not work if you have blacklisted the driver it needs. You need to decide which method to troubleshoot first; either do this or do the blacklisting and follow that up.
OK, sorry, I se it's a pci device. You'll need to

Code:

rmmod rtl8821ae insmod rtl8821ae

There may also be modules which depend on rtl8821ae. you will need to rmmod them too to get it to uninstall. Then reinsert (insmod or modprobe them all.)

Also, this chipset is known to have intermittent problems under linux. You can build and install the latest drivers from here:
https://medium.com/@elmaxx/rtl8821ae...4-4c1286524afa
There are instructions.

Quote:

Originally Posted by Nivla

so i just add blacklist rtl8821ae in the blacklist.conf?

Yes. Dit it work?

Quote:

Originally Posted by ptpi

I don't know if it will work, but...
if it's a usb device, unplug it; wait a few seconds, then plug it in again. DONT run airodump; just go straight to networkmanager. See if it works. (But this will not work if you have blacklisted the driver it needs. You need to decide which method to troubleshoot first; either do this or do the blacklisting and follow that up.
OK, sorry, I se it's a pci device. You'll need to

Code:

rmmod rtl8821ae insmod rtl8821ae

There may also be modules which depend on rtl8821ae. you will need to rmmod them too to get it to uninstall. Then reinsert (insmod or modprobe them all.)

I have tried the solution above
rmmod was fine but insmod it gives an error
insmod: ERROR : could not load module rtl8821ae: No such file or directory

Quote:

Originally Posted by _defalt

Yes. Dit it work?

I tried your solution and it blocked the wifi in rfkill , so rfkill is left with Bluetooth and I already undo it.
As I know rtl8821ae is the legit one.
Any other solution :(

Quote:

Originally Posted by ptpi

Also, this chipset is known to have intermittent problems under linux. You can build and install the latest drivers from here:
https://medium.com/@elmaxx/rtl8821ae...4-4c1286524afa
There are instructions.

I cant use the link :(

Quote:

Originally Posted by Nivla

I tried your solution and it blocked the wifi in rfkill , so rfkill is left with Bluetooth and I already undo it.
As I know rtl8821ae is the legit one.
Any other solution :(

Then this is the problem with a driver. Show the output of lspci -vv but don't post the whole output. There is a Network controller section in the output. Copy that.

Quote:

Originally Posted by _defalt

Then this is the problem with a driver. Show the output of lspci -vv but don't post the whole output. There is a Network controller section in the output. Copy that.

03:00.0 Network controller: Realtek Semiconductor Co., Ltd. RTL8821AE 802.11ac PCIe Wireless Network Adapter
Subsystem: Lenovo RTL8821AE 802.11ac PCIe Wireless Network Adapter
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 323
Region 0: I/O ports at 4000 [size=256]
Region 2: Memory at a4100000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable+ Count=1/1 Maskable- 64bit+
Address: 00000000fee00378 Data: 0000
Capabilities: [70] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 <64us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE+ FLReset- SlotPowerLimit 10.000W
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr+ UncorrErr- FatalErr- UnsuppReq- AuxPwr+ TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s L1, Exit Latency L0s <512ns, L1 <64us
ClockPM+ Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM L0s L1 Enabled; RCB 64 bytes Disabled- CommClk+
ExtSynch- ClockPM+ AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR+, OBFF Via message/WAKE#
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis+, LTR+, OBFF Disabled
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v2] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr+ BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr+
AERCap: First Error Pointer: 00, GenCap+ CGenEn- ChkCap+ ChkEn-
Capabilities: [140 v1] Device Serial Number 00-e0-4c-ff-fe-87-2b-01
Capabilities: [150 v1] Latency Tolerance Reporting
Max snoop latency: 3145728ns
Max no snoop latency: 3145728ns
Capabilities: [158 v1] L1 PM Substates
L1SubCap: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+ L1_PM_Substates+
PortCommonModeRestoreTime=150us PortTPowerOnTime=150us
L1SubCtl1: PCI-PM_L1.2+ PCI-PM_L1.1+ ASPM_L1.2+ ASPM_L1.1+
T_CommonMode=0us LTR1.2_Threshold=163840ns
L1SubCtl2: T_PwrOn=150us
Kernel driver in use: rtl8821ae
Kernel modules: rtl8821ae

It's definitely a problem with driver. You have to search how to install rtl8821ae driver in linux.

Media Report Analysis - Widow in battle

Quote:

Originally Posted by _defalt

It's definitely a problem with driver. You have to search how to install rtl8821ae driver in linux.

Will do, thanks for helping :) But because of this problem, I don't have access to wifi in Linux :(

Why can"t you use the link I posted? It is a link for the driver you need, and it is a working link.

_defalt, can you verify this link is working?
https://medium.com/@elmaxx/rtl8821ae...4-4c1286524afa

Quote:

Originally Posted by ptpi

_defalt, can you verify this link is working?
https://medium.com/@elmaxx/rtl8821ae...4-4c1286524afa

It's working fine for me.

Quote:

Originally Posted by ptpi

Why can"t you use the link I posted? It is a link for the driver you need, and it is a working link.

I tried getting in using three devices and different wifi. :(
or anyone can do me a favour and give me screenshots😭

Quote:

Originally Posted by Nivla

I tried getting in using three devices and different wifi. :(
or anyone can do me a favour and give me screenshots��

http://weblight.in/?lite_url=https%3...4-4c1286524afa

Quote:

Originally Posted by _defalt

http://weblight.in/?lite_url=https%3...4-4c1286524afa

thanks the links working, but if i cant access to wifi ,how do i use apt get

The page explains how to do it ...but you will need a working internet connection in Linux.
If you do some googling, you can find the driver in Windows, then save it and boot into Linux and copy it from your Windows C: drive. But there is a bit of work to do there; you might have some quick learning to do.
Can you use a phone's data connection to get Linux to access the internet? It's pretty straightforward if you can just get some sort of internet connection working.

Quote:

Originally Posted by ptpi

The page explains how to do it ...but you will need a working internet connection in Linux.
If you do some googling, you can find the driver in Windows, then save it and boot into Linux and copy it from your Windows C: drive. But there is a bit of work to do there; you might have some quick learning to do.
Can you use a phone's data connection to get Linux to access the internet? It's pretty straightforward if you can just get some sort of internet connection working.

there is no way of getting internet in linux, guess i have to use windows and copy the files to linux.

But how do i install after i copied the files😊 sudo install xxxxxx?

Use LAN wire or connect with mobile data by USB tethering.

Quote:

Originally Posted by _defalt

Use LAN wire or connect with mobile data by USB tethering.

wow it didnt occured to me using usn tethering as i dont have the lan cable slot.
thanks mate :)

i ran into some problems when using
make and sudo make install part

make
make -C /lib/modules/4.9.0-kali3-amd64/build M=/root/rtlwifi_new modules
make[1]: *** /lib/modules/4.9.0-kali3-amd64/build: No such file or directory. Stop.
Makefile:58: recipe for target 'all' failed
make: *** [all] Error 2

help? :(

You need to make sure the kernel headers are installed....
Did you have any errors when running

Code:

sudo apt-get install linux-headers-generic build-essential git

?
And, just checking, you are doing this with a hard drive installed Kali or a Persistence Kali which is working properly?
I had issues with the Kali Live from the standard repository; had to download the weekly build. But don't do that yet. It might not be your problem.
Is it a functioning Kali Live with Persistence which you are trying to install the driver for?

I don't think Kali has linux-headers-generic. I can"t see it anyway. You will need to work out which kernel you are running

Code:

uname -r

and then install the headers for that kernel.

Code:

sudo apt-get install linux-headers-4.12.0-kali1-686 [FOR EXAMPLE]

Hopefully this will work.
I could be wrong here. Can you check whether you have kernel headers installed? Do let me know if I'm on the wrong track.

Quote:

Originally Posted by ptpi

I don't think Kali has linux-headers-generic. I can"t see it anyway.

Kali doesn't use generic headers.
The require command in kali is sudo apt-get install linux-headers-$(uname -r)

The one you mentioned is also same.

generic-headers are available for ubuntu

Guys, My wifi is fixed!!!

But the thing is I didnt follow your steps because i was messing with fluxion, and somehow it ended crashing my kali linux and i cant boot into kali. So I ended up deleting the whole system and reinstall it.

After reinstall and blocking ideapad

the wifi was fixed!!!!
so thanks guys and the end hahahaha!

Show the output of cat /etc/modrobe.d/blacklist.conf

Quote:

Originally Posted by _defalt

Show the output of cat /etc/modrobe.d/blacklist.conf

same as last time

blacklist ideapad_laptop

Quote:

Originally Posted by Nivla

Guys, My wifi is fixed!!!

But the thing is I didnt follow your steps because i was messing with fluxion, and somehow it ended crashing my kali linux and i cant boot into kali. So I ended up deleting the whole system and reinstall it.

After reinstall and blocking ideapad

the wifi was fixed!!!!
so thanks guys and the end hahahaha!

Apparently my wifi is broken again ,same like last time. help?

Quote:

Originally Posted by _defalt

Kali doesn't use generic headers.
The require command in kali is sudo apt-get install linux-headers-$(uname -r)

The one you mentioned is also same.

generic-headers are available for ubuntu

sudo apt-get install linux-headers-$(uname -r)
Reading package lists... Done
Building dependency tree
Reading state information... Done
E: Unable to locate package linux-headers-4.9.0-kali3-amd64
E: Couldn't find any package by glob 'linux-headers-4.9.0-kali3-amd64'
E: Couldn't find any package by regex 'linux-headers-4.9.0-kali3-amd64'

sudo apt-get update && sudo apt-get dist-upgrade && sudo apt-get install linux-headers-$(uname -r)