-
MDK3 on 5Ghz
Can the MDK3 tool be used on the 5Ghz range? I am using the beacon flood mode with a specific ESSID and BSSID as follows:
Code:
mdk3 mon0 b -v names.txt -c 40
but it is not picked up by my laptop or cell phone wifi scanner (both 5Ghz capable).
If MDK3 cannot be used on the 5Ghz range, what is a good tool to create traffic on a specific channel on the 5 and 2.4Ghz ranges?
This is a follow up to my previous post here.
I am using hostapd to try and create an ap (I don't need anyone to be able to connect or anything, I just need to be able to put a network on a specific channel).
When trying to put the ap on a 5ghz channel I get the error
Code:
wlan1: IEEE 802.11 Configured channel (40) not found from the channel list of current mode (1) IEEE 802.11g
The output of the command is:
Code:
root@kali:~# hostapd -dd hostapd.conf
random: Trying to read entropy from /dev/random
Configuration file: hostapd.conf
nl80211: interface wlan1 in phy phy0
rfkill: initial event: idx=0 type=1 op=0 soft=0 hard=0
nl80211: Using driver-based off-channel TX
nl80211: Add own interface ifindex 3
nl80211: Set mode ifindex 3 iftype 3 (AP)
nl80211: Create interface iftype 6 (MONITOR)
nl80211: New interface mon.wlan1 created: ifindex=7
nl80211: Add own interface ifindex 7
BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits)
nl80211: Regulatory information - country=US
nl80211: 2402-2472 @ 40 MHz
nl80211: 5170-5250 @ 40 MHz
nl80211: 5250-5330 @ 40 MHz
nl80211: 5490-5600 @ 40 MHz
nl80211: 5650-5710 @ 40 MHz
nl80211: 5735-5835 @ 40 MHz
nl80211: Added 802.11b mode based on 802.11g information
Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=27 dBm
Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=27 dBm
Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=27 dBm
Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=27 dBm
Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=27 dBm
Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=27 dBm
Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=27 dBm
Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=27 dBm
Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=27 dBm
Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=27 dBm
Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=27 dBm
Allowed channel: mode=2 chan=36 freq=5180 MHz max_tx_power=17 dBm
Allowed channel: mode=2 chan=38 freq=5190 MHz max_tx_power=17 dBm
Allowed channel: mode=2 chan=40 freq=5200 MHz max_tx_power=17 dBm
Allowed channel: mode=2 chan=42 freq=5210 MHz max_tx_power=17 dBm
Allowed channel: mode=2 chan=44 freq=5220 MHz max_tx_power=17 dBm
Allowed channel: mode=2 chan=46 freq=5230 MHz max_tx_power=17 dBm
Allowed channel: mode=2 chan=48 freq=5240 MHz max_tx_power=17 dBm
Allowed channel: mode=2 chan=149 freq=5745 MHz max_tx_power=30 dBm
Allowed channel: mode=2 chan=151 freq=5755 MHz max_tx_power=30 dBm
Allowed channel: mode=2 chan=153 freq=5765 MHz max_tx_power=30 dBm
Allowed channel: mode=2 chan=155 freq=5775 MHz max_tx_power=30 dBm
Allowed channel: mode=2 chan=157 freq=5785 MHz max_tx_power=30 dBm
Allowed channel: mode=2 chan=159 freq=5795 MHz max_tx_power=30 dBm
Allowed channel: mode=2 chan=161 freq=5805 MHz max_tx_power=30 dBm
Allowed channel: mode=2 chan=165 freq=5825 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=27 dBm
Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=27 dBm
Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=27 dBm
Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=27 dBm
Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=27 dBm
Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=27 dBm
Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=27 dBm
Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=27 dBm
Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=27 dBm
Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=27 dBm
Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=27 dBm
wlan1: IEEE 802.11 Configured channel (40) not found from the channel list of current mode (1) IEEE 802.11g
wlan1: IEEE 802.11 Hardware does not support configured channel
Could not select hw_mode and channel. (-4)
wlan1: Unable to setup interface.
hostapd.conf:
Code:
root@kali:~# cat hostapd.conf
country_code=US
driver=nl80211
interface=wlan1
ssid=test
#ieee80211n=1
hw_mode=g
channel=40
macaddr_acl=0
device_name=wlan1
beacon_int=15
wireless card info:
Code:
root@kali:~# iwconfig wlan1
wlan1 IEEE 802.11abgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=27 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:on
Code:
root@kali:~# iw list
Wiphy phy0
Band 1:
Capabilities: 0x2f2
HT20/HT40
Static SM Power Save
RX Greenfield
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 2-streams
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 2 usec (0x04)
HT RX MCS rate indexes supported: 0-15, 32
TX unequal modulation not supported
HT TX Max spatial streams: 2
HT TX MCS rate indexes supported may differ
Frequencies:
* 2412 MHz [1] (27.0 dBm)
* 2417 MHz [2] (27.0 dBm)
* 2422 MHz [3] (27.0 dBm)
* 2427 MHz [4] (27.0 dBm)
* 2432 MHz [5] (27.0 dBm)
* 2437 MHz [6] (27.0 dBm)
* 2442 MHz [7] (27.0 dBm)
* 2447 MHz [8] (27.0 dBm)
* 2452 MHz [9] (27.0 dBm)
* 2457 MHz [10] (27.0 dBm)
* 2462 MHz [11] (27.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Band 2:
Capabilities: 0x2f2
HT20/HT40
Static SM Power Save
RX Greenfield
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 2-streams
Max AMSDU length: 3839 bytes
No DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 2 usec (0x04)
HT RX MCS rate indexes supported: 0-15, 32
TX unequal modulation not supported
HT TX Max spatial streams: 2
HT TX MCS rate indexes supported may differ
Frequencies:
* 5180 MHz [36] (17.0 dBm)
* 5190 MHz [38] (17.0 dBm)
* 5200 MHz [40] (17.0 dBm)
* 5210 MHz [42] (17.0 dBm)
* 5220 MHz [44] (17.0 dBm)
* 5230 MHz [46] (17.0 dBm)
* 5240 MHz [48] (17.0 dBm)
* 5250 MHz [50] (disabled)
* 5260 MHz [52] (20.0 dBm) (radar detection)
* 5270 MHz [54] (20.0 dBm) (radar detection)
* 5280 MHz [56] (20.0 dBm) (radar detection)
* 5290 MHz [58] (20.0 dBm) (radar detection)
* 5300 MHz [60] (20.0 dBm) (radar detection)
* 5310 MHz [62] (20.0 dBm) (radar detection)
* 5320 MHz [64] (20.0 dBm) (radar detection)
* 5500 MHz [100] (20.0 dBm) (radar detection)
* 5510 MHz [102] (20.0 dBm) (radar detection)
* 5520 MHz [104] (20.0 dBm) (radar detection)
* 5530 MHz [106] (20.0 dBm) (radar detection)
* 5540 MHz [108] (20.0 dBm) (radar detection)
* 5550 MHz [110] (20.0 dBm) (radar detection)
* 5560 MHz [112] (20.0 dBm) (radar detection)
* 5570 MHz [114] (20.0 dBm) (radar detection)
* 5580 MHz [116] (20.0 dBm) (radar detection)
* 5590 MHz [118] (20.0 dBm) (radar detection)
* 5600 MHz [120] (disabled)
* 5610 MHz [122] (disabled)
* 5620 MHz [124] (disabled)
* 5630 MHz [126] (disabled)
* 5640 MHz [128] (disabled)
* 5650 MHz [130] (disabled)
* 5660 MHz [132] (20.0 dBm) (radar detection)
* 5670 MHz [134] (20.0 dBm) (radar detection)
* 5680 MHz [136] (20.0 dBm) (radar detection)
* 5690 MHz [138] (20.0 dBm) (radar detection)
* 5700 MHz [140] (20.0 dBm) (radar detection)
* 5745 MHz [149] (30.0 dBm)
* 5755 MHz [151] (30.0 dBm)
* 5765 MHz [153] (30.0 dBm)
* 5775 MHz [155] (30.0 dBm)
* 5785 MHz [157] (30.0 dBm)
* 5795 MHz [159] (30.0 dBm)
* 5805 MHz [161] (30.0 dBm)
* 5825 MHz [165] (30.0 dBm)
* 4920 MHz [-16] (disabled)
* 4940 MHz [-12] (disabled)
* 4960 MHz [-8] (disabled)
* 4980 MHz [-4] (disabled)
Code:
root@kali:~# iw reg get
country US:
(2402 - 2472 @ 40), (3, 27)
(5170 - 5250 @ 40), (3, 17)
(5250 - 5330 @ 40), (3, 20), DFS
(5490 - 5600 @ 40), (3, 20), DFS
(5650 - 5710 @ 40), (3, 20), DFS
(5735 - 5835 @ 40), (3, 30)
The wireless card is this one from NewEgg.
-
-
Hi,
Did you fig out a way ?
I am attempting something similar on dlink d803 5ghz mimo
no effect..
-
I have it working for 5GHz
Only worked on it for 2 minutes, minimal changes.
Main points, change the relevant lines with those below:
int chans [MAX_CHAN_COUNT] = { 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 0 };
in "char generate_channel()" change
c = (random() % 14) + 1;
to
c = 36; // for a specific channel
You can set up an enum or struct or whatever you like to expand on this and still use the random function to chose a switch/case or do it however you like. your choice.
Then the important thing.... on your wireless interface:
run "sudo iwconfig wlan1 channel 36"
so hopefully you have already put it into monitor mode via:
sudo ifconfig wlan1 down
sudo iwconfig wlan1 mode monitor
sudo ifconfig wlan1 up
sudo iwconfig wlan1 <--- Check for Mode:Monitor
sudo iwconfig wlan1 channel 36 <----- set the channel number like i did before
sudo mdk3 wlan1 b -f test.txt <--- will load text file with SSIDs and always use channel 36 even without passing in the channel number option "-c" as i hardcoded it.
That's it, it's working for my needs.
If someone wants to set up a proper channel number selection then go ahead, i won't be, i have what i need. but please paste it in the reply section here for others.
I just thought i'd throw this out there for others who need something similar.
Throw me a message and i'll try to reply.
