can you show your results after the reboot, as i did all of that before and it didnt work
Printable View
can you show your results after the reboot, as i did all of that before and it didnt work
i tried it again, and now this is working for me, did it on a normal boot not in a VM, thanks for the help bro
ignore the attached image, uploaded the wrong one
In my opinion its useful, lets say you want to make a evil twin attack its easier to make the client connect to your fake router since they get better reception. But for recieving data you need to raise the tx power of the router/client or get a better antenna/use a directional antenna to focus the signal better, but thats another story. This is just for educational purposes and should never be used for illegal purposes.
Thats not possible in this case since the card is region locked.. This guide works perfect.
Very useful when on "vacation" in regions where its allowed to use tx rate of 30
ifconfig wlan0 down
iw reg set BZ # new Region. BO does not work any more
iwconfig wlan0 txpower 30
ifconfig wlan0 up
though risky but if you wish -
for increasing TX power - Copy paste the following commands into a text file and save it in Home Directory as - WifiTxBoost
apply following commands to increase TX power (when needed) -Code:#!/bin/bash
echo "hello, root!"
echo " taking down wlan0"
ifconfig wlan0 down
sleep 3
echo "setting Region to Bolivia"
iw reg set GY
sleep 3
echo "setting TxPower to 30"
iwconfig wlan0 txpower 30
sleep 2
echo "starting wlan0"
ifconfig wlan0 up
echo "pulling wlan0 interface up"
iwconfig
sleep 5
echo "good bye"
(you may edit file with wlan1 too, the monitor mode (wlan1mon will be as per TX power set)Code:chmod +x WifiTxBoost
./WifiTxBoost
i here put a simple list of commands before starting penetration testing - (i assume that you are using 2 network cards)
save these commands in a text file and apply these commands before starting any testing -
thanking you.Code:ifconfig -a
macchanger -m 00:01:02:03:04:05 eth0
iw wlan0 interface add wlan0mon type monitor
ifconfig wlan0 down
ifconfig wlan0mon down
macchanger -m 00:02:03:04:05:06 wlan0
macchanger -m 00:04:05:06:07:08 wlan0mon
chmod +x WifiTxBoost
./WifiTxBoost
ifconfig wlan0 up
ifconfig wlan0mon up
ifconfig wlan1 down
macchanger -m 00:03:04:05:06:07 wlan1
ifconfig wlan1 up
iwconfig
ifconfig -a
Just a question on tx power. I setup your script and this is the output. Wondering if I'm getting 20 or 30dBm? Using Kali v2
root@kali:~# ./wifitx.sh
hello, root!
taking down wlan0
setting Region to GY
setting TxPower to 30
starting wlan0
pulling wlan0 interface up
wlan0 IEEE 802.11bgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm
Retry short limit:7 RTS thr=2347 B Fragment thr:off
Encryption key:off
Power Management:off
lo no wireless extensions.
eth0 no wireless extensions.
good bye
root@kali:~# iw reg get
country GY: DFS-UNSET
(2402 - 2482 @ 40), (N/A, 30), (N/A)
(5735 - 5835 @ 80), (N/A, 30), (N/A)
root@kali:~#
forget this tutorial it doesn't work. read here: https://forums.kali.org/showthread.p...-via-UART-JTAG
I'm able to change to TX Power for my Alfa AWUS036H but not for my new AWUS036NHR v.2
AWUS036NHR v.2
wlan0 IEEE 802.11bgn ESSID off/any
Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm
Retry short limit:7 RTS thr=2347 B Fragment thr off
Encryption key off
Power Management off
AWUS036H
wlan1 IEEE 802.11bg ESSID off/any
Mode:Managed Access Point: Not-Associated Tx-Power=30 dBm
Retry short limit:7 RTS thr off Fragment thr off
Encryption key off
Power Management off
Does it work for anyone? Does it has any advantage over the default value (20) ?
Thanks
can somehelp to update this tutorial for kali linux 2.0
im struggle for a week and still unsuccessful. please help guys!