Page 2 of 3 FirstFirst 123 LastLast
Results 51 to 100 of 143

Thread: Troubleshooting Wireless Drivers

  1. #51
    I put my usb wireless adapter in monitor mode but when I start airodump-by this happens ioctl (siocsifflags) failed: Connection timed out

    I am running Kali Linux 1.0.7 in virtual box please help

  2. #52
    Join Date
    2014-Jul
    Posts
    1

    Question BCM43142 wireless drivers Issue on kali 1.0.7 kernel 3.14

    I just dual-booted kali 1.0.7 kernel 3.14 and i searched everywhere for a solution to make my wireless card bcm43142 work in kali linux, I found some drivers here: http://www.broadcom.com/support/802.11/linux_sta.php , but I didn't know how to make them work, I tried this: http://www.kalilinux.net/community/t...k-in-kali.814/ , but didn't work because it only works on kernel 3.12. HELP ME PLEASE, thank you.

  3. #53
    Join Date
    2014-Jul
    Posts
    1
    Quote Originally Posted by ach173 View Post
    I just dual-booted kali 1.0.7 kernel 3.14 and i searched everywhere for a solution to make my wireless card bcm43142 work in kali linux, I found some drivers here: http://www.broadcom.com/support/802.11/linux_sta.php , but I didn't know how to make them work, I tried this: http://www.kalilinux.net/community/t...k-in-kali.814/ , but didn't work because it only works on kernel 3.12. HELP ME PLEASE, thank you.
    I faced screen flickering issues with default b43 drivers for BCM4331. Screen flickers every few seconds when Wifi is on, no issues when Wifi is switched off.
    Replaced the b43 drivers with the STA drivers direct from Broadcom and the flickering was gone.

    BCM43142 is supported with the current STA drivers.
    1) Download the file to a USB drive
    2) Follow the steps in the readme

  4. #54
    Join Date
    2014-Jul
    Posts
    1

    wifi slower in kali

    in my laptop i have just install the kali linux.
    in the same machine i have windows 7 ,debian and kali linux.
    i connect to intenerte via wirless chipset inter N-3010.
    Either in debier or windows i have a good band width (32-50 MBS)
    but in the kali linux i only get 7Mbs.
    Bouth in debian an kali i have the same driver.

    please can you help me to solve it .

    Thanks.

    In debian I have the flowing
    lsmod | grep iw
    Code:
    iwlwifi               166761  0 
    mac80211              192806  1 iwlwifi 
    cfg80211              137243  2 mac80211,iwlwifi

    Code:
    wlan0     IEEE 802.11bgn  ESSID:"XXXXXXX"  
              Mode:Managed  Frequency:2.462 GHz  Access Point: F8:8E:85:D1:19:0A   
              Bit Rate=65 Mb/s   Tx-Power=15 dBm   
              Retry  long limit:7   RTS thr:off   Fragment thr:off 
              Encryption key:off 
              Power Management:off 
              Link Quality=58/70  Signal level=-52 dBm  
              Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0 
              Tx excessive retries:11  Invalid misc:149   Missed beacon:0
    lspci
    Code:
    0d:00.0 Network controller: Intel Corporation Centrino Wireless-N 1030 [Rainbow Peak] (rev 34)
    in the kali linux
    lsmod | grep iw
    Code:
    iwldvm                130998  0 
    mac80211              488308  1 iwldvm 
    iwlwifi                87784  1 iwldvm 
    cfg80211              436618  3 iwlwifi,mac80211,iwldvm
    iwconfig
    Code:
    wlan0     IEEE 802.11bgn  ESSID:"xxxxxxxxx"  
              Mode:Managed  Frequency:2.462 GHz  Access Point: F8:8E:85:D1:19:0A   
              Bit Rate=1 Mb/s   Tx-Power=15 dBm   
              Retry short limit:7   RTS thr:off   Fragment thr:off 
              Encryption key:off 
              Power Management:off 
              Link Quality=64/70  Signal level=-46 dBm  
              Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0 
              Tx excessive retries:0  Invalid misc:1800   Missed beacon:0
    lspci
    Code:
    0d:00.0 Network controller: Intel Corporation Centrino Wireless-N 1030 [Rainbow Peak] (rev 34)

  5. #55
    Join Date
    2014-Jul
    Posts
    1
    Hi

    I just started with kali linux and i need help!
    I made a Live CD of kali linux 32bit and its running great on my mac
    but i do not have internet on lan or wireless i tied everything
    I found a driver but i can't install it and this was no help: http://www.broadcom.com/docs/linux_s...30.223.248.txt

    Skype: sadrisadri215

    Thx Sadfiesch

  6. #56
    Join Date
    2014-Aug
    Posts
    2
    I am running on an Acer Aspire V5 laptop with a Broadcom BCM43228 wlan adapter (onboard).

    I cant get it to work no matter what I try. I have googled for 4 days now, tried all bugfixes i found.

    the b43 firmware installer gives the following error:

    " No chroot environment found. Starting normal installation."
    " This card is actually not tested. Please install the driver manually."

    Usually, the wl driver worked for me, but this time, no matter what i tried so far, was working to get it to work.
    Basically, the wl.ko module wont install / run properly.

    The funny thing is that on Debian Wheezy, the wl installer would run fine without errors and work perfectly.

    Note: I am a linux newbie. I have gained a little experience while working with Debian and recently switched to kali.

  7. #57
    Join Date
    2014-Aug
    Posts
    3
    I am currently having issues with Kali Linux on VMware. I used BackTrack 5 briefly a few years ago but im back at it again. The issue i have is wlan0 will not show up when i have LINKSYS wusb6300 plugged in and connected through VMware. I do not remember having this issue on BT5 as it was an easy plug in play (at least for me) and i was connected to my access point right away. Right now I cant even select wireless or even join any network because it is grayed out. Is there a new procedure or am i overlooking a very basic/novice step? My thread is still pending for approval in the support section. I have also read some of the guidelines on the site as well as watched videos on youtube (installing compat-wireless) but i still can not get wlan0 to show up. Any help is appreciated.
    Screenshot of my network set up (yes ive also to bridge and it wont work)

    Almost forgot, of course the only other way to connect to my network is wired "eth0" which is working properly.

  8. #58
    Join Date
    2014-Sep
    Posts
    1

    Network Adapter that supports Kali Linux? [10.9.4 Late 2013 Macbook Air?]

    Hello Everyone!

    Before I start, I would just like to say:

    I am completely new to Kali Linux. So please, don't judge.

    I am running Kali linux on a persistence live USB

    The machine I am using is an Apple Macbook Air 13'' (Late 2013)


    To start off I know that Kali Linux does not support the Wi-fi adapter of 2013 models, and if there are any ways to fix that please let me know (Trust me I've tried quite a lot to fix it but it doesn't work). Now that I got that out of the way may I just ask:
    Is there any Wi-fi adapter that supports mac (late 2013 models) and Kali Linux?
    If there are please tell me. I've been looking at the Alfa AWUS036NHA and have been wondering if it has any sort of compatibility with my machine. If there are any others (that obviously support injection, and yada yada) please tell me. It would be greatly appreciated .

    If you have any suggestions please let me know ASAP...

    Thank You So Much!

  9. #59
    Join Date
    2014-Sep
    Posts
    1
    I have a little problem, I decided to get an upgrade for my wireless. Seeing that Alfa got a good reputation I thought I give it a go, so i bought a Alfa AWUS036NHR (V1) with a 5db antenna.
    And then the fun starts, after spending hours and hours i still haven't got this thing working properly, i changed the db from 20 to 30, and all the other suggestions online, but nothing really seems to work.

    It performs really bad, even my on-board wireless does a better job, anyone out here that got this thing working properly?
    Sniffing only gets me a few results and is really really slow, and injecting doesn't seem to work well (not) either...

    Is there any hope to get this thing to act normal, or should i move on?

  10. #60
    Join Date
    2014-Feb
    Posts
    8
    OK, I'm done with my patience i had to register and ask for help.
    My hardware: Alfa awus036nh
    My problem: i cant access the internet ... it is really strange. I have listed all available wifi networks of the USB adapter, but if i try to connect it wont.
    The history: 1. I installed kali 1.0.2 amd64 and everything worked great ... after i perform "apt-get upgrade" the network manager showed that I'm connected, but couldn't access the internet nor my router over the IP 192.168.1.1.
    2. After i got stuck on the 1.0.2 (after "apt-get upgrade") i tried 1.0.3 amd64, and now I'm not able to connect to the wireless at all.

    I tried to put wlan0 (my integrated wireless card) down ("ifconfig wlan0 down"), but had no luck ... tried to put eth0 and lo down, but nothing ... i tried everything that i found googling, but there's not much information for Kali out there ATM.


    PLEASE HELP!!!!!!!!!!!!!!
    root@kali:~# iwconfig
    wlan0 IEEE 802.11bg ESSID:"XSDADA"
    Mode:Managed Frequency:2.437 GHz Access Point: XX:XX:XX:XX:XX
    Bit Rate=48 Mb/s Tx-Power=20 dBm
    Retry short limit:7 RTS thr: off Fragment thr: off
    Encryption key: off
    Power Management: off
    Link Quality=49/70 Signal level=-61 dBm
    Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
    Tx excessive retries:105 Invalid misc:13 Missed beacon:0

    lo no wireless extensions.

    eth0 no wireless extensions.
    *************************************************
    root@kali:~# ifconfig
    eth0 Link encap:Ethernet HWaddr XXXXXXXXXXXXXXXXX
    UP BROADCAST MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    inet6 addr: ::1/128 Scope:Host
    UP LOOPBACK RUNNING MTU:65536 Metric:1
    RX packets:583 errors: 0 dropped:0 overruns: 0 frame: 0
    TX packets:583 errors: 0 dropped:0 overruns: 0 carrier: 0
    collisions:0 txqueuelen:0
    RX bytes:47778 (46.6 KiB) TX bytes:47778 (46.6 KiB)

    wlan0 Link encap:Ethernet HWaddr xx:xx:xx:xx:xx:xx
    inet addr:xx:xx:xx:xx:xx:xx Bcast:xx:xx:xx:xx:xx:xx Mask:255.255.255.0
    inet6 addr: fe80::287:41ff:fe00:1883/64 Scope:Link
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:261 errors: 0 dropped: 0 overruns: 0 frame: 0
    TX packets:1095 errors: 0 dropped: 0 overruns: 0 carrier: 0
    collisions:0 txqueuelen:1000
    RX bytes:81536 (79.6 KiB) TX bytes:102042 (99.6 KiB)

    ************************************************** *
    root@kali:~# dmesg | tail
    [ 25.830192] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
    [ 25.830194] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
    [ 25.830196] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
    [ 27.761915] wlan0: authenticate with xx:xx:xx:xx:xx:xx
    [ 27.951110] wlan0: send auth to xx:xx:xx:xx:xx:xx (try 1/3)
    [ 27.954140] wlan0: authenticated
    [ 27.956601] wlan0: associate with xx:xx:xx:xx:xx:xx (try 1/3)
    [ 27.959103] wlan0: RX AssocResp from xx:xx:xx:xx:xx:xx (capab=0x431 status=0 aid=1)
    [ 27.960186] wlan0: associated
    [ 80.672507] fuse init (API version 7.22)
    [ 25.830192] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
    [ 25.830194] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
    [ 25.830196] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
    [ 27.761915] wlan0: authenticate with xx:xx:xx:xx:xx:xx
    [ 27.951110] wlan0: send auth to xx:xx:xx:xx:xx:xx (try 1/3)
    [ 27.954140] wlan0: authenticated
    [ 27.956601] wlan0: associate with xx:xx:xx:xx:xx:xx (try 1/3)
    [ 27.959103] wlan0: RX AssocResp from xx:xx:xx:xx:xx:xx (capab=0x431 status=0 aid=1)
    [ 27.960186] wlan0: associated
    [ 80.672507] fuse init (API version 7.22)
    Last edited by Alexcreator; 2014-10-21 at 18:28.

  11. #61
    Join Date
    2014-Feb
    Posts
    8
    Is anybody found a solution for this problem? Only I can connect to wifi but no internet...
    Last edited by Alexcreator; 2014-10-21 at 17:38.

  12. #62
    Join Date
    2014-Jun
    Location
    Greece
    Posts
    133
    Quote Originally Posted by Alexcreator View Post
    Is anybody found a solution for this problem? Only I can connect to wifi but no internet...
    Hi Alexcreator.
    You can try:

    1)Try to set CRDA:
    Code:
    iw reg set <your country code>
    e.g
    Code:
    iw reg set US
    it's very weird that dmesg shows you only 5GHz and 60 GHz band frequencies:
    [ 25.830192] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
    [ 25.830194] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
    [ 25.830196] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
    if you are unsure try to use world regulatory domain. Kali sets by default the world regulatory domain:
    Code:
    iw reg set 00
    dmesg should look like this:
    Code:
    [ 2275.325369] cfg80211: Calling CRDA to update world regulatory domain
    [ 2275.327933] cfg80211: Calling CRDA to update world regulatory domain
    [ 2275.330695] cfg80211: World regulatory domain updated:
    [ 2275.330697] cfg80211:  DFS Master region: unset
    [ 2275.330698] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
    [ 2275.330700] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
    [ 2275.330701] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
    [ 2275.330702] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
    [ 2275.330704] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
    [ 2275.330705] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
    [ 2275.330706] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
    See?

    2) Look at /etc/network/interfaces file. If there are other then those ones:
    auto lo
    iface lo inet loopback
    delete them and restart networking and networkmanager.
    Code:
    service network-manager stop
    service networking stop
    service networking start
    service network-manager start
    3) Try to give a static IP,. Network-manager->Edit connections.
    4) See if you can ping a site. Maybe it's a DNS resolving problem.
    If you can't ping any site look at /etc/resolv.conf file and add a DNS server: e.g. OPEN DNS servers:
    Code:
    nameserver 208.67.222.222
    nameserver 208.67.220.220
    you can add this also if you set a statip IP to your connection. step 3 above.
    5) Unload and load your wireless NICs driver
    Code:
    modprobe -r <your driver>
    modprobe <your driver>
    6) See your iptables.
    7) Try to use a different wireless NIC.
    8) Have patience

    That's all for now. Good luck!
    Security always begins with personal responsibility. - quietman7

  13. #63
    Join Date
    2014-Dec
    Posts
    9
    Hi,

    Like many of you i have problems with my wirless adapter, i am not able to update the driver of my rtl8723be wireless. As long is i am not able to install the driver for the wireless adapter i am not able to doe anything. some help would be apriciated very much. I have tried a lot of steps and was able to set up a wlan0 and wlan1 but was not able to do anything with it because it does not recognise my wirless adapter only eth0 and lo.

    Kind regards

  14. #64
    Join Date
    2014-Dec
    Posts
    5
    hi,
    i have the AWUS036NH ALFA , and iam trying to create a simple access point
    iam connected to the internet through the wlan0 and trying to share it over awus036nh(Ralink RT2870/3070),wlan1
    but when i try to connect to my access point , its always disconnected , stuck on obtaining ip address , connecting and disconnecting immediately etc ...
    so what i have to do , here what i did
    ifconfig wlan1 down
    airmon-ng start wlan1
    airodump-ng mon0
    airbase-ng -a FC:5B:39:E05:C5 --essid COA-OLC -c 11 mon0
    -----------------------------------------------
    ifconfig at0 10.0.0.1 netmask 255.255.255.0
    ifconfig at0 mtu 1400
    route add -net 10.0.0.0 netmask 255.255.255.0 gw 10.0.0.1
    iptables --flush
    iptables --table nat --flush
    iptables --delete-chain
    iptables --table nat --delete-chain
    echo 1 > /proc/sys/net/ipv4/ip_forward
    iptables -t nat -A PREROUTING -p udp -j DNAT --to 172.18.180.1
    iptables -P FORWARD ACCEPT
    iptables --append FORWARD --in-interface at0 -j ACCEPT
    iptables --table nat --append POSTROUTING --out-interface wlan0 -j MASQUERADE
    iptables -t nat -A PREROUTING -p tcp --destination-port 80 -j REDIRECT --to-port 10000
    dhcpd -cf /etc/dhcpd.conf -pf /var/run/dhcpd.pid at0
    /etc/init.d/isc-dhcp-server start
    echo
    -----------------------------------
    dhcp conf file is like follows
    ddns-update-style none;
    authoritative;
    log-facility local7;
    subnet 10.0.0.0 netmask 255.255.255.0 {
    range 10.0.0.100 10.0.0.200;
    option domain-name-servers 172.18.180.1;
    option routers 10.0.0.1;
    option broadcast-address 10.0.0.255;
    default-lease-time 600;
    max-lease-time 7200;
    }
    ANOTHER THING THAT I RECENTLY NOTICED : WHEN I SIMPLY LAUNCH
    airbase-ng -e freewifi mon0
    the broadcasting channel keep changing by it self on airodump-ng monitor ???
    please help me ..
    Last edited by constantinex; 2015-01-12 at 16:25.

  15. #65
    Join Date
    2015-Jan
    Posts
    3
    hi guys i bought a acer laptop with a bcm43228 and then i install kali, update, upgrade everything, install STA driver to get my wireless card working, but no way for aircXck-ng suite especially the monitor mode wasn't working, then in fact the only way to make it working and it's working really good so the trick after days of fight is to update your kernel image and sources to at least 2.17+, i upgrade to 2.18 rc5, then update your grub, install driver b43 fw cutter and b43 driver, then make sure your driver WL ( if was working on your 2.14 kali system) is unload or absent, then modprobe b43 and ssd and you got it ... Everything is working now ! make a persistent for all boot, and you roxx !

    sorry for my french english

    Take care cheers guys

    wizzhard

  16. #66
    Join Date
    2015-Feb
    Posts
    5
    so i definately need some answers..
    ive came accross so much answers yet no solutions..
    my issue is that on my uefi gaming laptop i installed kali linux .
    although everything else is working smooth, my wifi card cannot be detected.
    i do lspci and i get :

    3b:00.0 Network controller: Broadcom Corporation Device 43b1 (rev 03)


    so i do iwconfig :

    eth0 no wireless extensions.

    lo no wireless extensions


    ive literally tried everything... i came accross this post here :

    http://superuser.com/questions/77536...k-in-dual-boot

    to use this other driver but i don't wanna jump to that until i know for certain it will be solution..
    i even tried to edit my /etc/apt/sources.list
    i also tried to fresh install and find card again..
    dmesg output is :

    too freaking long to put idk its stressing me out.. i know i will find the answer but this is like a last resort ..
    ive even tried to use previous fixes from backtrack.. nothing
    Last edited by sickn3ss; 2015-02-17 at 07:57.

  17. #67
    Join Date
    2015-Feb
    Posts
    2

    unable to set 30 dBm wireless card.

    hey guys,
    i am having a problem with my Realtek Semiconductor Corp. RTL8187 Wireless Adapter.
    i am trying to set the txpower to 30 after one year to scan networks,
    i just recently upgraded my kali install and try to boost the signal.
    this is what i did...
    ifconfig wlan0 down << no problems so far ...
    iw reg set BO << no error..
    ifconfig wlan0 up << no prob
    but then when i check the settings with iwconfig it still says Tx-Power 20 dBm
    so i put it down again ..
    then i try iwconfig wlan0 txpower 30, ifconfig wlan0 up and still no changes.
    any body has any solution for this?
    i never had this problem.
    checked the network manager service, network service stopt it started it, did it again but some how i am unable the set the 20 dBm to 30 dBm.
    thanks in advance!

  18. #68

    Question Wireless card BCM4311 issues: Compaq Presario V6000

    I am a novice user on most linux and ubuntu os. Been using Kali Linux for almost a year now. But still having problems with my Broadcom Wireless Card BCM4311 on my (HP) Compaq Presario V6000. When it was Windows Xp originally, it decided to go out. I had disabled it, uninstalled it from the hardware device manager, and rebooted the laptop and it worked for a short period. I also had a munufacter problem with the display showing color problems, turning pink and had a line through the screen. I eventually stopped using the laptop for some number of years cause i had bought a few others over the course of time. So once i started having some issues with the others i decided to go back into the closet to get the laptop out. I then decided to reformat it to Windows 7 and update the Graphics card and got it to work, but it would act up every now and then. So i said screw it and replaced it with Kali. That ended up fixing my graphics issue. But still nothing on the wireless card. I updated the Bios using Bart PE and winPHLASH and the exe setup. Still nothing. I had tried installing and reinstalling b43-fwcutter, as well as some others. I have seen a suggestion for bcmwl-kernel-source but i get no candidate in the terminal. i have updated, upgraded, and dist-upgrade, updated grub and kernel and still nothing. Im Currently using 3.18.0-kali1-686-pae. i have played around with the blacklisting and modprobs, and the rfkill unblock. nothing.. please help.. There has to be some kind of way to make it work. Im using a Ralink usb card, but it isnt mine. im just borrowing it to fix this **** thing..

  19. #69
    Join Date
    2015-Feb
    Posts
    2
    I have problem with my Alfa AWUS036NHA adapter, when i connect it to Kali installed on vBOx it only shows me a few wifi networks and most of them are locked so i cant connect to them, on windows 7 i see way more avilable networks and i can connect to 2 of them. Do i need to install some drivers for this adapter on linux kali and if so can anybody give me a quick tutorial?

  20. #70
    Join Date
    2015-Feb
    Posts
    2
    I just want to add some informations. I'v reinstalled Kali on my VirtualBox and when i connect my adapter pc slow down, then when i click on networks it find few wifi connections but i am unable to connect to them , no matter how strong signal is, there is 3 bar strong connection and i am still unable to connect. Can somebody help me out please?

  21. #71
    Join Date
    2015-Feb
    Posts
    5
    so just update .
    got the driver installed but its not loaded ... ill post if i find anything.

  22. #72
    Join Date
    2015-Feb
    Posts
    5
    i found the answer with my google.fu!! i think

    http://www.kalilinux.net/threads/tut...y-waldorf.391/

    this link helped me a lot it involves an upgrade good luck !!

  23. #73
    Join Date
    2015-Apr
    Posts
    3
    Hi Im having some trouble with my Alfa card AWUS036NHA. Im running Kali on Virtualbox on my mid 2013 Mac running 10.9 and for some reason my Alfa card randomly disconnects after about 10-15 minutes of being connected to Kali Linux. Its really getting annoying so how can I fix it?

  24. #74
    Join Date
    2015-Feb
    Posts
    5
    @reaganrockz if your using virtual box are you bridge network connection in virtual machine settings ??!! That's usually how vm gets the internet . u might wanna install VM tools. If ur trying aircrack to test how secure your wifi is you need a separate WiFi USB card it won't work with host hardware. Kali does require careful prep research before u get the hardware. I found out the hard way.

  25. #75
    Join Date
    2015-Feb
    Posts
    5
    So I have 43b1 running WL driver but I don't have monit0r mode. The driver from what I have read WL driver doesn't support aircrack. I have yet to find a driver to the 43b1 out there working besides the WL I've read other drivers work but fails when I try to install. But does anyone have some type of hint to my issue ? I would appreciate it I've been using Google.fu for a couple months tirelessly and no solution yet..

  26. #76
    Join Date
    2015-May
    Posts
    1
    This will fix it.

    http://askubuntu.com/questions/55868...reless-drivers
    Go here, follow instructions to find out what your wifi device is.

    Once you know, scroll down to the table called BROADCOM WIRELESS TABLE (Updated 21 February 2015)

    This will tell you the package to install

    EG.

    apt-get install firmware-b43-installer

    Once installed, turn on the wifi hardware switch. Then on next to network.

  27. #77
    Join Date
    2015-May
    Posts
    1
    Hi. I had bought Edimax EW-7811UTC AC600 Wireless USB and I want to install the drivers on linux to have ethernet. How I can install Edimax EW-7811UTC AC600 Wireless USB with no internet (no ethernet) ? In the instruction manual it states that "An active connection is required for Linux driver installation". Having no access to wired network I'm unable to follow the steps in manual and was wondering whether there's an alternative way of installing it without the internet connection.
    Edimax manual:
    http://www.edimax.com/images/Image/Q...English%29.pdf
    How I can install the driver without internet?
    PS Sorry for my english!

  28. #78
    Join Date
    2015-May
    Posts
    3
    Hi,
    i'm new in kali linux.
    i have an issue with the wifi connections.
    installing the newwst version of kali from the official website on virtual box.
    plug the USB wireless adapter (TP-LINK).
    also, i noticed wlan0 on #ifconfig command.
    on the network setting configure NAT

    my problem is that i cannot see any wireless networks.
    i followed few guides from youtube but with no luck.
    it show me that i'm wired connected.
    i attached screenshot bellow.
    please kindly assist me.
    Capture.jpg

    additional information:
    noticed stage behavior with :
    #airmon-ng start wlan0
    instead creating mon0 interface, when i type #ifconfig, i saw that wlan0 changed to wlan0mon
    and with#airodump-ng command on wlan0mon i didn't see any wireless network.
    Last edited by danan; 2015-05-26 at 09:31.

  29. #79
    Join Date
    2015-Jun
    Posts
    3
    My Kali dual boot windows 8.1(Dell inspiron N4050) after update wrong wireless:
    - When not updated yet. Everything fine.
    - After updated and restart it's automatic conected wifi still have network.
    - But if i disconect wifi and it not appear any wifi anymore.
    - It's show:
    ***uname -a***
    Code:
    Linux kali 3.18.0-kali3-amd64 #1 SMP Debian 3.18.6-1~kali2 (2015-03-02) x86_64 GNU/Linux
    ***airmon-ng check kill***
    Code:
    Killing these processes:
    
      PID Name
     3090 wpa_supplicant
    *************lsb_release -a************
    Code:
    No LSB modules are available.
    Distributor ID:	Kali
    Description:	Kali GNU/Linux 1.1.0
    Release:	1.1.0
    Codename:	moto
    ***sudo rfkill list***
    Code:
    0: hci0: Bluetooth
    	Soft blocked: no
    	Hard blocked: no
    1: phy0: Wireless LAN
    	Soft blocked: no
    	Hard blocked: no
    ***airmon-ng start wlan0***
    Code:
    Found 3 processes that could cause trouble.
    If airodump-ng, aireplay-ng or airtun-ng stops working after
    a short period of time, you may want to kill (some of) them!
    
      PID Name
     2993 NetworkManager
     3095 wpa_supplicant
     3116 dhclient
    
    PHY	Interface	Driver		Chipset
    
    phy0	wlan0		brcmsmac	Broadcom on bcma bus, information limited
    		(mac80211 monitor mode vif enabled for [phy0]wlan0 on [phy0]wlan0mon)
    		(mac80211 station mode vif disabled for [phy0]wlan0)
    ***ifconfig***
    Code:
    lo        Link encap:Local Loopback  
              inet addr:127.0.0.1  Mask:255.0.0.0
              inet6 addr: ::1/128 Scope:Host
              UP LOOPBACK RUNNING  MTU:65536  Metric:1
              RX packets:308 errors:0 dropped:0 overruns:0 frame:0
              TX packets:308 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:0 
              RX bytes:24568 (23.9 KiB)  TX bytes:24568 (23.9 KiB)
    
    wlan0mon  Link encap:UNSPEC  HWaddr CC-AF-78-8E-89-4B-3A-30-00-00-00-00-00-00-00-00  
              UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
              RX packets:165 errors:0 dropped:165 overruns:0 frame:0
              TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
              collisions:0 txqueuelen:1000 
              RX bytes:40654 (39.7 KiB)  TX bytes:0 (0.0 B)
    ***dmesg | tail***
    Code:
    [ 2722.995879] cfg80211:  DFS Master region: unset
    [ 2722.995883] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
    [ 2722.995891] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
    [ 2722.995898] cfg80211:   (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
    [ 2722.995903] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
    [ 2722.995909] cfg80211:   (5170000 KHz - 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
    [ 2722.995915] cfg80211:   (5250000 KHz - 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
    [ 2722.995921] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
    [ 2722.995927] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
    [ 2722.995933] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
    ***lsusb***
    Code:
    Bus 002 Device 004: ID 174c:55aa ASMedia Technology Inc. 
    Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
    Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 001 Device 005: ID 064e:8122 Suyin Corp. 
    Bus 001 Device 004: ID 0a5c:21bc Broadcom Corp. BCM2070 Bluetooth 2.1 + EDR
    Bus 001 Device 003: ID 0458:003a KYE Systems Corp. (Mouse Systems) NetScroll+ Mini Traveler / Genius NetScroll 120
    Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
    Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    ***lspci -nn -d 14e4:***
    Code:
    09:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01)
    ***lspci***
    Code:
    00:00.0 Host bridge: Intel Corporation 2nd Generation Core Processor Family DRAM Controller (rev 09)
    00:01.0 PCI bridge: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port (rev 09)
    00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09)
    00:16.0 Communication controller: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 (rev 04)
    00:1a.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 (rev 05)
    00:1b.0 Audio device: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller (rev 05)
    00:1c.0 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 (rev b5)
    00:1c.1 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 (rev b5)
    00:1c.3 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 (rev b5)
    00:1c.7 PCI bridge: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 8 (rev b5)
    00:1d.0 USB controller: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 (rev 05)
    00:1f.0 ISA bridge: Intel Corporation HM67 Express Chipset Family LPC Controller (rev 05)
    00:1f.2 SATA controller: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller (rev 05)
    00:1f.3 SMBus: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller (rev 05)
    01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Caicos [Radeon HD 6400M/7400M Series] (rev ff)
    05:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 05)
    09:00.0 Network controller: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller (rev 01)
    *** sudo lshw -C network***
    Code:
    *-network               
           description: Ethernet interface
           product: RTL8101E/RTL8102E PCI Express Fast Ethernet controller
           vendor: Realtek Semiconductor Co., Ltd.
           physical id: 0
           bus info: pci@0000:05:00.0
           logical name: eth0
           version: 05
           serial: 18:03:73:68:25:2d
           size: 10Mbit/s
           capacity: 100Mbit/s
           width: 64 bits
           clock: 33MHz
           capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
           configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=half firmware=rtl_nic/rtl8105e-1.fw latency=0 link=no multicast=yes port=MII speed=10Mbit/s
           resources: irq:26 ioport:d000(size=256) memory:f1104000-f1104fff memory:f1100000-f1103fff
      *-network
           description: Network controller
           product: BCM4313 802.11b/g/n Wireless LAN Controller
           vendor: Broadcom Corporation
           physical id: 0
           bus info: pci@0000:09:00.0
           version: 01
           width: 64 bits
           clock: 33MHz
           capabilities: pm msi pciexpress bus_master cap_list
           configuration: driver=bcma-pci-bridge latency=0
           resources: irq:19 memory:f7d00000-f7d03fff
    ***pyrit list_cores***
    Code:
    Pyrit 0.4.0 (C) 2008-2011 Lukas Lueg http://pyrit.googlecode.com
    This code is distributed under the GNU General Public License v3+
    
    The following cores seem available...
    #1:  'CPU-Core (SSE2)'
    #2:  'CPU-Core (SSE2)'
    #3:  'CPU-Core (SSE2)'
    #4:  'CPU-Core (SSE2)'
    ***sources.list***
    Code:
    deb http://mirror.gawsolutions.us/kali kali main non-free contrib
    deb-src http://mirror.gawsolutions.us/kali kali main non-free contrib
    deb http://mirror.gawsolutions.us/kali-security kali/updates main contrib non-free

  30. #80
    Join Date
    2015-Aug
    Posts
    11

    Question Ralink Technology, Corp. - MediaTek MT7601U Wireless Adapter can't installed

    dear all,
    recently i bought a cheap (made in china) wireless adapter based on - MediaTek - MT7601U Driver Chip
    i google a lot , but can't configure or install the adapter properly -
    below is lsusb command output -
    Code:
    root@kali:~# lsusb
    Bus 007 Device 005: ID 0cf3:9271 Atheros Communications, Inc. AR9271 802.11n
    Bus 007 Device 006: ID 148f:7601 Ralink Technology, Corp. MT7601U Wireless Adapter
    Bus 007 Device 004: ID 062a:4101 Creative Labs Wireless Keyboard/Mouse
    Bus 007 Device 002: ID 1a40:0101 Terminus Technology Inc. Hub
    Bus 007 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 004 Device 002: ID 08ff:2580 AuthenTec, Inc. AES2501 Fingerprint Sensor
    Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    Bus 001 Device 002: ID 03f0:171d Hewlett-Packard Bluetooth 2.0 Interface [Broadcom BCM2045]
    Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    root@kali:~#
    a kind request to give full guide lines to enable this adapter (while i already purchased it and too much curious to know why it is not installed ?)
    thanking you all.

    regards,

  31. #81
    Join Date
    2015-Aug
    Posts
    11
    i here give a brief details of commands used at starting penetration testing -

    ================================================== =============
    # change temporarily mac address of eth0

    Code:
    ifconfig | grep HWaddr
    ifconfig eth0 down
    ifconfig eth0 hw ether 00:00:00:00:00:02
    ifconfig eth0 up
    ifconfig -a
    ================================================== =============
    # multiple monitors creating under wlan0 / wlan1

    Code:
    iw wlan0 interface add mon0 type monitor
    iw wlan0 interface add mon1 type monitor
    ================================================== =============
    # to avoid network-manager conflict &&&& also mac spoofing

    Code:
    airmon-ng start mon0
    ifconfig mon0mon down
    macchanger -m 00:01:02:03:04:05 mon0mon  
    iwconfig mon0mon mode monitor
    ifconfig mon0mon up
    -------------------

    Code:
    airmon-ng start mon1
    ifconfig mon1mon down
    macchanger -m 00:01:02:03:04:05 mon1mon  
    iwconfig mon1mon mode monitor
    ifconfig mon1mon up
    ================================================== =============
    # if network not listed / disconnected - do apply following commands -

    Code:
    rfkill list all
    rfkill unblock all
    ctrl +F3 or sleep system & then start again
    ----------------------------------------------------------------------
    # do this if not proper connection start

    Code:
    service network-manager start 
    service avahi-daemon start
    ----------------------------------------------------------------------

    # at last

    Code:
    apt-get update 
    apt-get dist-upgrade
    ================================================== =============
    A SPECIAL THANKS TO --- https://forums.kali.org/member.php?17445-mmusket33
    Last edited by maulesh; 2015-09-07 at 17:53.

  32. #82
    Join Date
    2015-Aug
    Posts
    11
    Dear All,
    Ralink Technology, Corp. - MediaTek MT7601U Wireless Adapter can't installed (page-8) -
    Request to give solutions.
    Thanks

  33. #83
    Join Date
    2015-Sep
    Posts
    2
    Dears

    i have Nanostation M2 which is scanning in web based ( connected to Ethernet cable ) , how i can scan and do the airodump command and airocrack command in kali ? its not detecting as wireless interface and its not scanning.

    i am using the latest kali version on vmware workstation Capture.jpg

  34. #84
    Join Date
    2015-Jun
    Posts
    1
    hi
    i am sorry i was unable to give enough information previouly
    hp pavilion p018tu model and windows 8.1 single language. i am tried to bual boot with kali linux 2.0.installtion done successfully
    now problem is wifi and bluetooth are not working.i have some results for list of commands

    lspci returned

    "08:00.0 Network controller: Broadcom Corporation BCM43142 802.11b/g/n (rev 01)

    09:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller (rev 08)"


    dmesg (errors i found)

    [ 14.080349] bluetooth hci0: firmware: failed to load brcm/BCM43142A0-0a5c-216c.hcd (-2)

    [ 14.080351] bluetooth hci0: Direct firmware load for brcm/BCM43142A0-0a5c-216c.hcd failed with error -2


    root@kali:~# iwconfig
    eth0
    no wireless extensions.


    lo
    no wireless extensions.


    root@kali:~# ifconfig wlan0 up

    wlan0: ERROR while getting interface flags: No such device


    these are results i can provide....
    i have basic knowledge in kali linux.so please give me solution in brief

  35. #85
    Join Date
    2015-Sep
    Posts
    1
    I'm using Kali 2.0 and my usb wireless adapter is Airties Air 2315, I can't connect to net my adapters light doesn't opening but when I turn to Windows it's working fine, I'm booting kali from my USB flash drive.

  36. #86
    Join Date
    2015-Sep
    Posts
    2
    Dears any help for the pervious ?

  37. #87
    'airmon-ng wlan1' will not work! Please Help!
    Im running Kali from a live usb and im useing a AWUS036NHA when I 'ifconfig' I see the usb card under wlan1, but when I 'airmon-ng wlan1' I get:
    root@kali:~# airmon-ng start wlan1
    Found 5 processes that could cause trouble.
    If airodump-ng, aireplay-ng or airtun-ng stops working after
    a short period of time, you may want to kill (some of) them!

    PID Name
    1333 NetworkManager
    1462 wpa_supplicant
    1703 avahi-daemon
    1704 avahi-daemon
    2299 dhclient

    PHY Interface Driver Chipset

    phy0 wlan0 rt2800pci Ralink corp. RT3090 Wireless 802.11n 1T/1R PCIe
    phy2 wlan1 ath9k_htc Atheros Communications, Inc. AR9271 802.11n
    (mac80211 monitor mode vif enabled for [phy2]wlan1 on [phy2]wlan1mon)
    (mac80211 station mode vif disabled for [phy2]wlan1)

    Im completely and hoplessly stuck, please send help...

  38. #88
    I didnt mean to past the whole thing, im really just trying to figure out what these two are refurring too.

    (mac80211 monitor mode vif enabled for [phy1]wlan1 on [phy1]wlan1mon)

    (mac80211 station mode vif disabled for [phy1]wlan1)


    Also I have a column in my terminal before "Interface" thats called "PHY" that I dont know what it is and dont see it in any of the tutorials.

    PHY Interface Driver Chipset

    phy0 wlan0 rt2800pci Ralink corp. RT3090 Wireless 802.11n 1T/1R PCIe
    phy1 wlan1 ath9k_htc Atheros Communications, Inc. AR9271 802.11n

  39. #89
    Join Date
    2015-Oct
    Posts
    1
    i have an issue with kali linux that wifi freezes while using it. then i trun off my wifi and then conect again then it works and same process again and again.. but intenet works for windows at the same time.. plz help me

  40. #90
    Join Date
    2015-Nov
    Posts
    2

    wirrless usb problem

    Please help me for mt wireless card
    model: EnGenius EUB9603H USB Adapter


    lsusb:
    Code:
    Bus 002 Device 007: ID 1740:9603 Senao RTL8188S WLAN Adapter
    Bus 002 Device 004: ID 148f:5370 Ralink Technology, Corp. RT5370 Wireless Adapter
    Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 001 Device 003: ID 0e0f:0002 VMware, Inc. Virtual USB Hub
    Bus 001 Device 002: ID 0e0f:0003 VMware, Inc. Virtual Mouse
    Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub

    iwconfig:
    PHP Code:
    wlan2     IEEE 802.11bgn  ESSID:off/any  
              Mode
    :Managed  Access PointNot-Associated   Tx-Power=20 dBm   
              Retry short limit
    :7   RTS thr:off   Fragment thr:off
              Encryption key
    :off
              Power Management
    :off
              
    lo        no wireless extensions
    .

    eth0      no wireless extensions.

    wlan1     unassociated  Nickname:"rtl_wifi"
              
    Mode:Managed  Access PointNot-Associated   Sensitivity:0/0  
              Retry
    :off   RTS thr:off   Fragment thr:off
              Encryption key
    :off
              Power Management
    :off
              Link Quality
    :0  Signal level:0  Noise level:0
              Rx invalid nwid
    :0  Rx invalid crypt:0  Rx invalid frag:0
              Tx excessive retries
    :0  Invalid misc:0   Missed beacon:


    airmon-ng start wlan1:

    PHP Code:
    No interfering processes found
    PHY    
    Interface    Driver        Chipset

    null    wlan1        r8712u        Senao RTL8188S WLAN Adapterphy1    wlan2        rt2800usb    Ralink Technology
    CorpRT5370 
    [/QUOTE]

  41. #91
    Join Date
    2015-Nov
    Location
    Vitoria, Spain
    Posts
    2
    does Everyone know what can I do with my nexus 7 2013 (andr. 5.0) and m Alfa AWUS036NH to make them work?

    Thanks for helping

  42. #92
    Join Date
    2015-Nov
    Posts
    1
    Hi All,

    I'm having what might be a simple problem with my Alfa AWUS036NH. It shows up under ifconfif/iwconfig. I can see it under lsusb and lsmod (as rt2800), but I do not see an entry for it under lspci. The USB icon (Virtual Box) at the bottom is persistently red, never green. When I try to search for networks, it says "no networks" even though it works just fine on my host OS.

    I have updated and upgraded to no avail. Tried changing txpower without success. This is the output I get from dmesg

    ieee80211 phy1: rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x101c with error -110
    [ 4634.800865] ieee80211 phy1: rt2x00usb_vendor_request: Error - Vendor Request 0x07 failed for offset 0x101c with error -110
    [ 4636.428770] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready

    Thanks Bud

  43. #93
    Join Date
    2015-Nov
    Posts
    1
    Hi All,
    I am going crazy to use a AWUS036NH in KAli 2.0 VirtualBox.
    I cannot set the monitor mode.
    Here what happens:
    root@kali:~# ifconfig
    eth0 Link encap:Ethernet HWaddr 08:00:27:bf:ed:99
    inet addr:10.0.2.15 Bcast:10.0.2.255 Mask:255.255.255.0
    inet6 addr: fe80::a00:27ff:febf:ed99/64 Scope:Link
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:6 errors:0 dropped:0 overruns:0 frame:0
    TX packets:68 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:1528 (1.4 KiB) TX bytes:9925 (9.6 KiB)

    lo Link encap:Local Loopback
    inet addr:127.0.0.1 Mask:255.0.0.0
    inet6 addr: ::1/128 Scope:Host
    UP LOOPBACK RUNNING MTU:65536 Metric:1
    RX packets:20 errors:0 dropped:0 overruns:0 frame:0
    TX packets:20 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:0
    RX bytes:1200 (1.1 KiB) TX bytes:1200 (1.1 KiB)

    wlan1 Link encap:Ethernet HWaddr 00:c0:ca:59:01:a6
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:0 errors:0 dropped:0 overruns:0 frame:0
    TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)

    root@kali:~# iwconfig
    eth0 no wireless extensions.

    lo no wireless extensions.

    wlan1 IEEE 802.11bgn ESSIDff/any
    Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm
    Retry short limit:7 RTS thrff Fragment thrff
    Encryption keyff
    Power Managementff

    root@kali:~# airmon-ng start wlan1
    Found 5 processes that could cause trouble.
    If airodump-ng, aireplay-ng or airtun-ng stops working after
    a short period of time, you may want to kill (some of) them!

    PID Name
    548 NetworkManager
    695 dhclient
    867 avahi-daemon
    873 avahi-daemon
    883 wpa_supplicant

    PHY Interface Driver Chipset

    phy3 wlan1 rt2800usb Ralink Technology, Corp. RT2870/RT3070
    (mac80211 monitor mode vif enabled for [phy3]wlan1 on [phy3]wlan1mon)
    (mac80211 station mode vif disabled for [phy3]wlan1)


    root@kali:~# airodump-ng wlan1mon
    ioctl(SIOCSIWMODE) failed: Device or resource busy

    ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211,
    ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead. Make
    sure RFMON is enabled: run 'airmon-ng start wlan1mon <#>'
    Sysfs injection support was not found either.

    root@kali:~# lsusb
    Bus 001 Device 006: ID 148f:3070 Ralink Technology, Corp. RT2870/RT3070 Wireless Adapter
    Bus 001 Device 002: ID 80ee:0021 VirtualBox USB Tablet
    Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
    root@kali:~#


    Thanks

  44. #94
    Join Date
    2015-Nov
    Posts
    1
    Hey guys i have a problem with my dual booted kali on my macbook air 2013..

    I have successfully installed the drivers for the internal wireless card and i have ha stable Internet connection..
    But i cant bring the card in monitor mode..

    Thats the first time im using linux and i have no idiea how to fix this problem.

    -------------------------------------------------------------------------------------------------------------
    # iwconfig wlan0 mode monitor
    Error for wireless request "Set Mode" (8B06) :
    SET failed on device wlan0 ; Operation not supported.
    -------------------------------------------------------------------------------------------------------------
    uname -r
    4.0.0-kali1-amd64
    ------------------------------------------------------------------------------------------------------------
    lspci -nn
    03:00.0 Network controller [0280]: Broadcom Corporation BCM4360 802.11ac Wireless Network Adapter [14e4:43a0] (rev 03)
    ------------------------------------------------------------------------------------------------------------

    i have done 1000 of tuturials but nothing works for me
    I think that the drivers not support this...

    Please help me to bring the internal card in monitor mode

  45. #95
    Join Date
    2016-Jan
    Posts
    2
    Hello guys i'am trying to install my Huawei data card but i get this following error below.

    Install NDIS driver failed. The compiling environment is not all ready. Please check gcc, make and kernel build(/lib/modules/4.0.0-kali-686-pae/build) to be all installed?
    NDIS is disabled, and only Modem can be used.



    Can anyone help??

  46. #96
    Join Date
    2016-Feb
    Location
    California
    Posts
    112
    Quote Originally Posted by Zordon of Eltar View Post
    I put my usb wireless adapter in monitor mode but when I start airodump-by this happens ioctl (siocsifflags) failed: Connection timed out

    I am running Kali Linux 1.0.7 in virtual box please help
    Dear friend "Zordon of Eltar"
    pelase reffer this link
    https://taufanlubis.wordpress.com/20...-busy-problem/
    ------------------Contact: Skype : Gh0sT.sh ( 0 -->Zero )-------------------
    |
    /vvvvvvvvvvvv \-------------------------------------------------------------------------,,
    |^^^^^^^^ /===================================--""
    ################################################
    ----------The quieter you become,The more you will able to hear-----------
    ################################################

  47. #97
    Join Date
    2015-Nov
    Posts
    7
    macbook pro late 2013 BCM43 is not detected in any of kali versions 2.0/4.0/4.0.

  48. it is helpful to me, thanks. I solved the usp problem

  49. #99
    Join Date
    2016-Mar
    Posts
    1
    Hi there
    i'm having some problem with wifite
    ill explain it now
    it all started after installing kali on my laptop. Im newbie in this thing but i've allready managed to penetrate into some wifi.
    when I insstalled kali on my laptop my wlan card was OK i was able to connect on wifi to turn on wifite even crack some wep encryptions but problem started when I wanted to use airmon-ng so when I've started under my chipset was something like non-mac 8021 (i dont know exactly) so i was able to turn monitor mode on to see wifi netwroks around me but when i've used airodump-ng when i selected the target after long time it wasnt even then able to catch clients. I'm using broadcom b4312 wlan card laptop(HP 210 mini). after that yesterday i found that it's a wlan driver problem which can be solved. I have followed this site https://wiki.debian.org/wl so I've fixed that. But another problem shows up after starting wifite it says enabling monitor mode on wlan0... done and again same message appears and again and again. That's first problem but I didnt paid some attention on cuz i will not use wifite so much. Another problem shows up when I tried to change mac adrress with macchanger(ifconfig wlan0 down -> macchanger mac=xx:xx:xx:xx:xx:xx wlan0 ->) here is some photos about my problem please help i dont know what is it
    http://i.imgur.com/vtifSsC.jpg
    http://i.imgur.com/QcykuPn.jpg
    http://i.imgur.com/TnjclWq.jpg
    http://i.imgur.com/rEl795S.jpg
    http://i.imgur.com/TVr7MXc.jpg
    http://i.imgur.com/RkR3XvN.jpg
    http://i.imgur.com/8jHod4G.jpg
    I've tried finding on ineternet but nothing showed up like this please if someone konws how to solve this mail me I'm so desperated.
    Another note I've done all last updates and upgrades on my kali.
    please help help :'((((

  50. #100
    Join Date
    2016-Mar
    Posts
    1
    Hi there,i have a problem with my wireless card on kali linux.Can anyone help me how i can install the drive of it becouse it canot detect.The wifi is Qualcom Atheros AR9485 802.11b/g/n

Similar Threads

  1. Troubleshooting wireless pen testing
    By madmardegon in forum General Archive
    Replies: 1
    Last Post: 2016-10-10, 11:51
  2. Troubleshooting - Confirm nvidia drivers
    By jamesmartin in forum TroubleShooting Archive
    Replies: 0
    Last Post: 2015-09-11, 14:57
  3. troubleshooting for installing nvidia drivers on asus g551jm kali 2.0
    By HoseinHarami in forum TroubleShooting Archive
    Replies: 0
    Last Post: 2015-08-23, 15:18

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •