Hey Guys,
I have just upgraded to the latest version of Kali 3.7-Trunk-AMD64 from Kali 3.14-AMD-64
My wireless was working flawlessly before the upgrade and failed to work afterwards.
Initially I thought this was an issue with the kernel upgrade but think this maybe a hardware issue now as after using the old kernel the card worked at first but now randomly experiencing the same problem even with the old kernel.
I have not had had the card work at all with the new kernel however....
The network manager is listing 'device not ready'....when trying to ifconfig wlan0 up i received "SIOCCSIFLAGS input output error"
the device is listed under lspci:
02:00.0 Network controller: Ralink corp. Device 3290
02:00.1 Bluetooth: Ralink corp. Device 3298
06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
Here is the output for dmesg with the card WORKING
root@localhost:~# dmesg
[ 9.977923] cfg80211: World regulatory domain updated:
[ 9.977940] cfg80211: DFS Master region: unset
[ 9.977946] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.977955] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.977963] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.977970] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.977977] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.977984] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 10.562911] [drm] fb mappable at 0x80477000
[ 10.562924] [drm] vram apper at 0x80000000
[ 10.562929] [drm] size 4325376
[ 10.562934] [drm] fb depth is 24
[ 10.562938] [drm] pitch is 5632
[ 14.835533] loop: module loaded
[ 20.715731] Netfilter messages via NETLINK v0.30.
[ 26.458744] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt3290.bin'
[ 26.650435] rt2800pci 0000:02:00.0: firmware: direct-loading firmware rt3290.bin
[ 26.650466] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.37
[ 28.265469] ieee80211 phy0: rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy [0x00000068]
[ 29.865825] ieee80211 phy0: rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy [0x00000068]
[ 29.865847] ieee80211 phy0: rt2800pci_set_device_state: Error - Device failed to enter state 4 (-5)
[ 29.970416] r8169 0000:06:00.0: firmware: direct-loading firmware rtl_nic/rtl8168e-3.fw
[ 30.100444] r8169 0000:06:00.0 eth0: link down
[ 30.100585] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 31.794602] ieee80211 phy0: rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy [0x00000068]
[ 33.395062] ieee80211 phy0: rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy [0x00000068]
[ 33.395084] ieee80211 phy0: rt2800pci_set_device_state: Error - Device failed to enter state 4 (-5)
[ 35.011594] ieee80211 phy0: rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy [0x00000068]
[ 36.612329] ieee80211 phy0: rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy [0x00000068]
[ 36.612353] ieee80211 phy0: rt2800pci_set_device_state: Error - Device failed to enter state 4 (-5)
[ 305.745499] usb 3-1: new high-speed USB device number 2 using ehci-pci
[ 305.878841] usb 3-1: New USB device found, idVendor=0781, idProduct=5575
[ 305.878859] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 305.878869] usb 3-1: Product: Cruzer Glide
[ 2498.796408] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 2498.938388] r8169 0000:06:00.0 eth0: link down
[ 2498.938549] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 2501.118286] wlan0: authenticate with 2a:e1:4c:3f:6f:07
[ 2501.132880] wlan0: send auth to 2a:e1:4c:3f:6f:07 (try 1/3)
[ 2501.134090] wlan0: authenticated
[ 2501.135223] wlan0: AP has invalid WMM params (AIFSN=0 for ACI 0), disabling WMM
[ 2501.136666] wlan0: associate with 2a:e1:4c:3f:6f:07 (try 1/3)
[ 2501.138806] wlan0: RX AssocResp from 2a:e1:4c:3f:6f:07 (capab=0x411 status=0 aid=1)
[ 2501.138984] wlan0: associated
[ 2501.139072] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
THIS IS DMESG with the card not working
root@localhost:~# dmesg
[ 2.942772] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 2.943271] r8169 0000:06:00.0: irq 44 for MSI/MSI-X
[ 2.943731] r8169 0000:06:00.0 eth0: RTL8168evl/8111evl at 0xffffc900043ec000, 84:34:97:82:31:d3, XID 0c900800 IRQ 44
[ 2.943741] r8169 0000:06:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 2.965095] usb usb6: New USB device found, idVendor=1d6b, idProduct=0001
[ 7.371264] ACPI Error: [SSZE] Namespace lookup failure, AE_ALREADY_EXISTS (20131218/dsfield-211)
[ 7.371287] ACPI Error: Method parse/execution failed [\_SB_.ACAD._PSR] (Node ffff880064058a38), AE_ALREADY_EXISTS (20131218/psparse-536)
[ 7.371340] ACPI Exception: AE_ALREADY_EXISTS, Error reading AC Adapter state (20131218/ac-77)
[ 7.371571] ACPI Error: [SSZE] Namespace lookup failure, AE_ALREADY_EXISTS (20131218/dsfield-211)
[ 7.371582] ACPI Error: Method parse/execution failed [\_SB_.ACAD._PSR] (Node ffff880064058a38), AE_ALREADY_EXISTS (20131218/psparse-536)
[ 7.371594] ACPI Exception: AE_ALREADY_EXISTS, Error reading AC Adapter state (20131218/ac-77)
[ 7.371987] ACPI Error: [SSZE] Namespace lookup failure, AE_ALREADY_EXISTS (20131218/dsfield-211)
[ 7.371998] ACPI Error: Method parse/execution failed [\_SB_.ACAD._PSR] (Node ffff880064058a38), AE_ALREADY_EXISTS (20131218/psparse-536)
[ 7.772213] ACPI Warning: SystemIO range 0x0000000000000b00-0x0000000000000b07 conflicts with OpRegion 0x0000000000000b00-0x0000000000000b0f (\_SB_.PCI0.SMBS.SMB0) (20131218/utaddress-258)
[ 9.221497] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 3290, rev 0015 detected
[ 9.226142] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 3290 detected
[ 9.498040] cfg80211: World regulatory domain updated:
[ 9.498052] cfg80211: DFS Master region: unset
[ 9.498055] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.498060] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.498064] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.498068] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.498072] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.498075] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.530156] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 20.970130] Netfilter messages via NETLINK v0.30.
[ 25.567634] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt3290.bin'
[ 25.604457] rt2800pci 0000:02:00.0: firmware: direct-loading firmware rt3290.bin
[ 25.604490] ieee80211 phy0: rt2x00lib_request_firmware: Info - Firmware detected - version: 0.37
[ 27.221070] ieee80211 phy0: rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy [0x00000068]
[ 28.821540] ieee80211 phy0: rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy [0x00000068]
[ 28.821561] ieee80211 phy0: rt2800pci_set_device_state: Error - Device failed to enter state 4 (-5)
[ 28.957779] r8169 0000:06:00.0: firmware: direct-loading firmware rtl_nic/rtl8168e-3.fw
[ 29.080092] r8169 0000:06:00.0 eth0: link down
[ 29.080215] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 30.858373] ieee80211 phy0: rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy [0x00000068]
[ 32.458873] ieee80211 phy0: rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy [0x00000068]
[ 32.458895] ieee80211 phy0: rt2800pci_set_device_state: Error - Device failed to enter state 4 (-5)
[ 34.087114] ieee80211 phy0: rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy [0x00000068]
[ 35.691877] ieee80211 phy0: rt2800_wait_wpdma_ready: Error - WPDMA TX/RX busy [0x00000068]
[ 35.691901] ieee80211 phy0: rt2800pci_set_device_state: Error - Device failed to enter state 4 (-5)
[ 259.048126] FAT-fs (sdb1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Any guidance would be much appreciated!
Tony
