Results 1 to 3 of 3

Thread: Failure To Associate With, Packet Injection Issues

  1. #1
    Join Date
    2015-Jun
    Posts
    14

    Failure To Associate With, Packet Injection Issues

    I'm having some problems with reaver. I have a internal Wifi Card that does not do Packet Injection RTL8188EE. In fact it runs absolutely horribly on Linux period. The other card I have does packet injection rt2800usb I bought specifically for Linux.

    I wanted to do some security penetration on my own router and start learning more about Network Security. I have my A+ and Net+ I'd like to move onto Security certifications. I also need to learn more about Linux and get those Certs.

    I will try to keep out repetitive information and limit the post as much as possible.

    1) Run IfConfig note the Mac Address of existing Wifi Adapter, 1X:0X:bF:6X:1D:4X in this case

    2) Insert Wifi Card.Run ifConfig again. Note which Wlan the new card is by the mac address. In My case it is Wlan1

    3) airmon-ng start wlan1


    Code:
    Interface	Chipset		Driver
    
    wlan1		Unknown 	rt2800usb - [phy1]
    				(monitor mode enabled on mon0)
    wlan0		Unknown 	rtl8188ee - [phy0]
    4) airodump-ng mon0



    Code:
    XX:XD:XE:X9:XC:X8  -32     2421      294    2   6  54   WPA  TKIP   PSK  Lanane Family           
     X8:FX:BX:1X:XX:87  -62        3        0    0   1  54e  WPA2 CCMP   PSK  PapaGrammyZim           
     FE:F5:28:A0:C8:F8  -66        1        0    0  10  
    
    So On ....
    5) reaver -i mon0 -b XX:XD:XE:X9:XC:X8 -vv

    I get .....



    Code:
    [!] WARNING: Failed to associate with XX:XD:XE:X9:XC:X8 (ESSID: Lanane Family)
    [!] WARNING: Failed to associate with XX:XD:XE:X9:XC:X8 (ESSID: Lanane Family)
    [!] WARNING: Failed to associate with XX:XD:XE:X9:XC:X8 (ESSID: Lanane Family)
    [!] WARNING: Failed to associate with XX:XD:XE:X9:XC:X8 (ESSID: Lanane Family)
    [!] WARNING: Failed to associate with XX:XD:XE:X9:XC:X8 (ESSID: Lanane Family)
    [!] WARNING: Failed to associate with XX:XD:XE:X9:XC:X8 (ESSID: Lanane Family)
    [!] WARNING: Failed to associate with XX:XD:XE:X9:XC:X8 (ESSID: Lanane Family)
    [!] WARNING: Failed to associate with XX:XD:XE:X9:XC:X8 (ESSID: Lanane Family)
    [!] WARNING: Failed to associate with XX:XD:XE:X9:XC:X8 (ESSID: Lanane Family
    )

    6) I then tried aireplay-ng -9 wlan1

    Code:
    ioctl(SIOCSIWMODE) failed: Device or resource busy
    
    ARP linktype is set to 1 (Ethernet) - expected ARPHRD_IEEE80211,
    ARPHRD_IEEE80211_FULL or ARPHRD_IEEE80211_PRISM instead.  Make
    sure RFMON is enabled: run 'airmon-ng start wlan1 <#>'
    Sysfs injection support was not found either.
    I then got a popup box asking for my network password. It then reconnected my wifi that was supposed to be in monitor mode.

    Actually it looks like it connected my internal wifi, not the external USB one

    Code:
    oem-HP-15-Notebook-PC oem # iwconfig
    mon0      IEEE 802.11bgn  Mode:Monitor  Tx-Power=20 dBm   
              Retry  long limit:7   RTS thr:off   Fragment thr:off
              Power Management:on
              
    wlan1     IEEE 802.11bgn  ESSID:off/any  
              Mode:Managed  Access Point: Not-Associated   Tx-Power=20 dBm   
              Retry  long limit:7   RTS thr:off   Fragment thr:off
              Encryption key:off
              Power Management:on
              
    eth0      no wireless extensions.
    
    lo        no wireless extensions.
    
    wlan0     IEEE 802.11bgn  ESSID:"Lanane Family"  
              Mode:Managed  Frequency:2.437 GHz  Access Point: XX:XX:XX:XX:XX:XX   
              Bit Rate=1 Mb/s   Tx-Power=20 dBm   
              Retry  long limit:7   RTS thr=2347 B   Fragment thr:off
              Encryption key:off
              Power Management:off
              Link Quality=62/70  Signal level=-48 dBm  
              Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
              Tx excessive retries:0  Invalid misc:0   Missed beacon:0
    7) After some tinkering around I typed in ... Typed in aireplay-ng -9 mon2

    Code:
    17:59:58  Trying broadcast probe requests...
    17:59:59  Injection is working!
    18:00:00  Found 1 AP 
    
    18:00:00  Trying directed probe requests...
    18:00:00  XX:XX:XX:XX:XX:XX - channel: 6 - 'Lanane Family'
    18:00:00  Ping (min/avg/max): 1.319ms/3.800ms/10.868ms Power: -34.55
    18:00:00  29/30:  96%

    Also if I test for packet injection by typing in aireplay-ng -9 wlan1 or aireplay-ng -9 wlan2 I get an error .... It only says I have packet injection when I check the mon not the wlan.


    After doing all this I am still getting :


    Code:
    [!] WARNING: Failed to associate with XX:XD:XE:X9:XC:X8 (ESSID: Lanane Family)
    [!] WARNING: Failed to associate with XX:XD:XE:X9:XC:X8 (ESSID: Lanane Family)
    [!] WARNING: Failed to associate with XX:XD:XE:X9:XC:X8 (ESSID: Lanane Family)
    [!] WARNING: Failed to associate with XX:XD:XE:X9:XC:X8 (ESSID: Lanane Family)

    The router is literally 10 feet away from me.

  2. #2
    Join Date
    2015-Jun
    Posts
    7
    Wireshark is your best friend here. Make sure you are actually sending out associate requests and see exactly how the router is responding. Also wifi is very .. how do i say 'finicky' meaning that sometimes atleast im my experience things just simply wont work and you need to unplug the card or in rare cases give your pc a reboot.

  3. #3
    Join Date
    2015-Jun
    Posts
    14
    I will look into Wireshark. For some reason I just did thee following and it validated packet injection. My problem now is I can't find a single AP out of 3 locations, my own router included, that are able to be cracked by Reaver. Wash always shows no reslts. Anyways here is what I did from a fresh restart and it works perfectly

    su Root

    airmon-ng start wlan1

    aireplay-ng -9 mon0

    airodump-ng mon0 (SHOWED MULTIPLE AP AT MULTIPLE LOCATIONS)

    wash -i mon0 (NO RESULTS EVER SHOW UP)

    Testing Packet Injections works flawlessly and shows nearby AP

    --------------------------------------------------------------------------------------------

    At this point I need to try different tools to test crack my router. I want the program that is more friendly to beginners but willing to try anything.

Similar Threads

  1. Replies: 3
    Last Post: 2017-06-11, 03:23
  2. Replies: 2
    Last Post: 2017-02-20, 22:52
  3. Packet injection on 5 GHz non-DFS channels strange behaviour
    By misterade in forum General Archive
    Replies: 0
    Last Post: 2016-11-25, 10:32

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •