Page 7 of 7 FirstFirst ... 567
Results 61 to 66 of 66

Thread: Bully modified to implement pixiewps attack

  1. #61
    Junior Member
    Join Date
    Dec 2016
    Posts
    3
    Hi all,

    I just installed bully on my system and I was curious if I was able to crack my own wifi router. My question: is it normal that the pin set from bully never change to random but always the same? What is causing this?

    Code:
    [+] Rx(Beacon) = 'Timeout'   Next pin '11533917'
    [+] Rx(Beacon) = 'Timeout'   Next pin '11533917'
    [+] Rx( Auth ) = 'Timeout'   Next pin '11533917'
    [+] Rx(Beacon) = 'Timeout'   Next pin '11533917'
    [+] Sent packet not acknowledged after 3 attempts
    [+] Tx( Assn ) = 'Timeout'   Next pin '11533917'
    [+] Rx(Beacon) = 'Timeout'   Next pin '11533917'
    [+] Rx(Beacon) = 'Timeout'   Next pin '11533917'
    [+] Rx(Beacon) = 'Timeout'   Next pin '11533917'
    [+] Rx(  ID  ) = 'Timeout'   Next pin '11533917'
    [+] Sent packet not acknowledged after 3 attempts
    [+] Tx(DeAuth) = 'Timeout'   Next pin '11533917'
    [+] Rx(Beacon) = 'Timeout'   Next pin '11533917'
    [!] Received M2D or out of sequence WPS Message
    [+] Rx(M2D/M3) = 'WPSFail'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx( Assn ) = 'Timeout'   Next pin '11533917'
    [+] Rx(Beacon) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx( Auth ) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx(  ID  ) = 'Timeout'   Next pin '11533917'
    [+] Rx(Beacon) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'WPSFail'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx(  M1  ) = 'Timeout'   Next pin '11533917'
    [+] Rx( Assn ) = 'Timeout'   Next pin '11533917'

  2. #62
    Junior Member
    Join Date
    Nov 2016
    Location
    Outer space
    Posts
    24
    It stuck if is not able to perform the attempt. Maybe your home's router has PBC activated (push button connect) and needs to push the button physically in order to accept wps connections. You can check it using airodump-ng with --wps parameter (available from aircrack 1.2 rc2 I think, not sure). Start scanning and let it long time. After a few minutes, on WPS column start to appear interesting data like this (PBC) on some routers.
    Last edited by v1s1t0r; 2016-12-06 at 12:16 PM. Reason: more detailed data

  3. #63
    Senior Member
    Join Date
    Jul 2013
    Location
    United States
    Posts
    516
    Or your connection is crappy, unsupported wireless card, WPS is enabled but not configure, AP is low on entropy, there are literally 1,000 reasons as to why there may be a problem.

    It helps if you give more information about the target. Since it is yours, you should be able to do that.

  4. #64
    Junior Member
    Join Date
    Nov 2016
    Location
    sook
    Posts
    1
    hello annarchyy ? i got some problem at bully install pixiewps. (make: *** [bully] Error 1)

  5. #65
    Junior Member
    Join Date
    Nov 2016
    Location
    Outer space
    Posts
    24
    Sorry for answer maybe too late. To build correctly bully with latest Kali releases you must "downgrade" libssl-dev package. I mean, if you do
    apt-get remove libssl-dev
    and then
    apt-get install libssl1.0-dev
    . After this you can compile successfully bully following the github instructions, you know:

    git clone https://github.com/aanarchyy/bully
    cd bully*/
    cd src/
    make
    make install
    Hope it helps.

  6. #66
    Junior Member
    Join Date
    Nov 2016
    Location
    Outer space
    Posts
    24
    Fresh news. Yesterday wiire (the author of pixiewps) updated the aanarchyy bully project. The version is still the 1.1 and it hasn't any new feature but he solved the problems on compilation. He removed the dependency of libssl-dev. Now the compilation is very fast and flawless.

    https://github.com/aanarchyy/bully

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •