Hey Guys
I can't seem to get an interface to show up for my PCIe wireless card. I've tried a couple of solutions that I found through google like this this and a whole slew of other solutions with fresh install in between but I run into the same issue with almost every one.
To start out, I'll give you a bit of information about my machine.
uname -a
Linux Network 4.6.0-kali1-amd64 #1 SMP Debian 4.6.4-1kali1 (2016-07-21) x86_64 GNU/Linux
lsb_release -a
No LSB modules are available.
Distributor ID: Kali
Description: Kali GNU/Linux Rolling
Release: kali-rolling
Codename: kali-rolling
lspci (removed unrelated devices)
0c:00.0 Network controller: Broadcom Corporation BCM4360 802.11ac Wireless Network Adapter (rev 03)
dmesg | tail
dmesg | tail
[ 170.176897] ipheth 1-2:4.2: ipheth_tx_timeout: TX timeout
[ 180.177079] ipheth 1-2:4.2: ipheth_tx_timeout: TX timeout
[ 190.177207] ipheth 1-2:4.2: ipheth_tx_timeout: TX timeout
[ 200.177391] ipheth 1-2:4.2: ipheth_tx_timeout: TX timeout
[ 210.177629] ipheth 1-2:4.2: ipheth_tx_timeout: TX timeout
[ 220.177811] ipheth 1-2:4.2: ipheth_tx_timeout: TX timeout
[ 230.178012] ipheth 1-2:4.2: ipheth_tx_timeout: TX timeout
[ 240.178192] ipheth 1-2:4.2: ipheth_tx_timeout: TX timeout
[ 250.178373] ipheth 1-2:4.2: ipheth_tx_timeout: TX timeout
[ 260.178523] ipheth 1-2:4.2: ipheth_tx_timeout: TX timeout
rfkill list
(Blank)
ifconfig -a
eth0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
ether 1c:b7:2c:ac:1c:20 txqueuelen 1000 (Ethernet)
RX packets 0 bytes 0 (0.0 B)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 0 bytes 0 (0.0 B)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
device interrupt 27 memory 0xfe800000-fe820000
eth1: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet netmask 255.255.255.240 broadcast
inet6 2600:380:523e:6a91:b890:888f:4fe0:80e2 prefixlen 64 scopeid 0x0<global>
inet6 2600:380:523e:6a91:b070:2dff:fe7c:7851 prefixlen 64 scopeid 0x0<global>
inet6 prefixlen 64 scopeid 0x20<link>
ether b2:70:2d:7c:78:51 txqueuelen 1000 (Ethernet)
RX packets 87665 bytes 98055799 (93.5 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 65828 bytes 9090100 (8.6 MiB)
TX errors 24 dropped 0 overruns 0 carrier 0 collisions 0
lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
inet 127.0.0.1 netmask 255.0.0.0
inet6 ::1 prefixlen 128 scopeid 0x10<host>
loop txqueuelen 1 (Local Loopback)
RX packets 5364 bytes 1287847 (1.2 MiB)
RX errors 0 dropped 0 overruns 0 frame 0
TX packets 5364 bytes 1287847 (1.2 MiB)
TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0
iwconfig
lo no wireless extensions.
eth1 no wireless extensions.
eth0 no wireless extensions.
What I've figured out so far is that I need to install some headers in order to get it to work but whatever steps I follow I always end up with a "fatal error, module not found" or something along those lines when i try to run modprobe wl. I've been able to get wireless working on kali previously so I'm tearing my hair out trying to find a solution. I'd appreciate any help you guys can offer.
Thanks