Results 1 to 3 of 3

Thread: What's your boot time?

  1. #1
    Join Date
    2013-Apr
    Posts
    10

    Question What's your boot time?

    Hello everyone. I've been having quite the slow boot time. Around where I bolded it seems to really slow it down. Is this normal? What's your boot time?

    [ 6.359174] sd 6:0:0:0: [sdb] Attached SCSI removable disk
    [ 7.837816] EXT4-fs (sda4): re-mounted. Opts: (null)
    [ 8.116260] EXT4-fs (sda4): re-mounted. Opts: errors=remount-ro
    [ 8.280484] loop: module loaded
    [ 15.591902] r8169 0000:01:00.0: firmware: agent loaded rtl_nic/rtl8105e-1.fw into memory

    [ 15.775295] r8169 0000:01:00.0 eth0: link down
    [ 15.775323] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
    [ 15.776655] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
    [ 15.784259] iwlwifi 0000:02:00.0: Radio type=0x2-0x0-0x0
    [ 16.157177] iwlwifi 0000:02:00.0: L1 Enabled; Disabling L0S
    [ 16.164851] iwlwifi 0000:02:00.0: Radio type=0x2-0x0-0x0
    [ 16.375799] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
    [ 17.556185] wlan0: authenticate with e8:40:f2:88:d7:5c
    [ 17.564443] wlan0: send auth to e8:40:f2:88:d7:5c (try 1/3)
    [ 17.566470] wlan0: authenticated
    [ 17.569895] wlan0: associate with e8:40:f2:88:d7:5c (try 1/3)
    [ 17.573198] wlan0: RX AssocResp from e8:40:f2:88:d7:5c (capab=0x411 status=0 aid=1)
    [ 17.575302] wlan0: associated
    [ 17.575341] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready

  2. #2
    Join Date
    2013-Mar
    Posts
    269
    From cold boot to log-on screen takes roughly 1 minute for me. If you like to make things a bit faster you could always disable startup services. The startup scripts are located in the init.d folder. The easiest way to do this, while also making it easy to re-enable the scripts is to use a simple startup manager. I recommend one called rcconf, simple to use, and easy to understand. However, before so take a look at this page for other options. http://www.debianadmin.com/manage-li...p-scripts.html
    You might be having a slow down because your networking is initializing?
    Fact, Science and the Pursuit of Knowledge. Working to secure your networks from threats; Outside and Within.

  3. #3
    Join Date
    2013-Apr
    Posts
    10
    Thank you for your help. I do have another question though. During install it was asking me to install some non-free drivers. Do you think it may have to do with those? How would I get them?

Similar Threads

  1. Kali persistence stuck in boot time
    By blackronin in forum TroubleShooting Archive
    Replies: 1
    Last Post: 2014-07-11, 07:38
  2. Boot time is zero on RPi
    By northpole in forum ARM Archive
    Replies: 0
    Last Post: 2013-04-09, 11:36

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •