Results 1 to 14 of 14

Thread: problem with wifi usb keys TP-LINK TL-WN725N v3

  1. #1
    Join Date
    2018-Oct
    Posts
    17

    problem with wifi usb keys TP-LINK TL-WN725N v3

    hello community kali

    I am under kali since not very long, I have the version of kali: 4.17.0-kali1-686-pae . I can not put my wifi keys , with the command "airmon-ng " :

    airmon-ng :

    PHY Interface Driver Chipset

    null wlan0 r8188eu Realtek Semiconductor Corp. RTL8188EUS 802.11n Wireless Network Adapter

    ifconfig
    eth0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
    ether 54:04:a6:97:6b:a5 txqueuelen 1000 (Ethernet)
    RX packets 0 bytes 0 (0.0 B)
    RX errors 0 dropped 0 overruns 0 frame 0
    TX packets 0 bytes 0 (0.0 B)
    TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

    lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536
    inet 127.0.0.1 netmask 255.0.0.0
    inet6 ::1 prefixlen 128 scopeid 0x10<host>
    loop txqueuelen 1000 (Boucle locale)
    RX packets 3060 bytes 247356 (241.5 KiB)
    RX errors 0 dropped 0 overruns 0 frame 0
    TX packets 3060 bytes 247356 (241.5 KiB)
    TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

    usb0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
    inet 192.168.42.155 netmask 255.255.255.0 broadcast 192.168.42.255
    inet6 fe80::4cc8:12ff:fef2:2f45 prefixlen 64 scopeid 0x20<link>
    ether 4e:c8:12:f2:2f:45 txqueuelen 1000 (Ethernet)
    RX packets 31411 bytes 20615389 (19.6 MiB)
    RX errors 7 dropped 0 overruns 0 frame 7
    TX packets 28278 bytes 4277862 (4.0 MiB)
    TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

    wlan0: flags=4099<UP,BROADCAST,MULTICAST> mtu 1500
    ether 50:3e:aa:72:a9:a9 txqueuelen 1000 (Ethernet)
    RX packets 0 bytes 0 (0.0 B)
    RX errors 0 dropped 0 overruns 0 frame 0
    TX packets 0 bytes 0 (0.0 B)
    TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0

    i tried to install the drivers but i still have the same answer: E: the files is not find or something like that.Could you help me find a solution to solve my problem. Thanks in advance

  2. #2
    Join Date
    2016-Dec
    Posts
    421
    It may work, you'll have to do an injection test using aireplay-ng.

    Check the documentation for airmon-ng and aireplay-ng

  3. #3
    Join Date
    2018-Oct
    Posts
    17
    oot@ReckH:~# airmon-ng

    PHY Interface Driver Chipset

    null wlan0 r8188eu Realtek Semiconductor Corp. RTL8188EUS 802.11n Wireless Network Adapter

    root@ReckH:~# aireplay-ng

    Aireplay-ng 1.3 - (C) 2006-2018 Thomas d'Otreppe
    https://www.aircrack-ng.org

    usage: aireplay-ng <options> <replay interface>

    Filter options:

    -b bssid : MAC address, Access Point
    -d dmac : MAC address, Destination
    -s smac : MAC address, Source
    -m len : minimum packet length
    -n len : maximum packet length
    -u type : frame control, type field
    -v subt : frame control, subtype field
    -t tods : frame control, To DS bit
    -f fromds : frame control, From DS bit
    -w iswep : frame control, WEP bit
    -D : disable AP detection

    Replay options:

    -x nbpps : number of packets per second
    -p fctrl : set frame control word (hex)
    -a bssid : set Access Point MAC address
    -c dmac : set Destination MAC address
    -h smac : set Source MAC address
    -g value : change ring buffer size (default: 8)
    -F : choose first matching packet

    Fakeauth attack options:

    -e essid : set target AP SSID
    -o npckts : number of packets per burst (0=auto, default: 1)
    -q sec : seconds between keep-alives
    -Q : send reassociation requests
    -y prga : keystream for shared key auth
    -T n : exit after retry fake auth request n time

    Arp Replay attack options:

    -j : inject FromDS packets

    Fragmentation attack options:

    -k IP : set destination IP in fragments
    -l IP : set source IP in fragments

    Test attack options:

    -B : activates the bitrate test

    Source options:

    -i iface : capture packets from this interface
    -r file : extract packets from this pcap file

    Miscellaneous options:

    -R : disable /dev/rtc usage
    --ignore-negative-one : if the interface's channel can't be determined,
    ignore the mismatch, needed for unpatched cfg80211
    --deauth-rc rc : Deauthentication reason code [0-254] (Default: 7)

    Attack modes (numbers can still be used):

    --deauth count : deauthenticate 1 or all stations (-0)
    --fakeauth delay : fake authentication with AP (-1)
    --interactive : interactive frame selection (-2)
    --arpreplay : standard ARP-request replay (-3)
    --chopchop : decrypt/chopchop WEP packet (-4)
    --fragment : generates valid keystream (-5)
    --caffe-latte : query a client for new IVs (-6)
    --cfrag : fragments against a client (-7)
    --migmode : attacks WPA migration mode (-8)
    --test : tests injection and quality (-9)

    --help : Displays this usage screen

    No replay interface specified.

    then

  4. #4
    Join Date
    2016-Dec
    Location
    Canada
    Posts
    221
    rfkill unblock all
    rfkill list

  5. #5
    Join Date
    2018-Oct
    Posts
    17
    root@ReckH:~# aireplay-ng

    Aireplay-ng 1.3 - (C) 2006-2018 Thomas d'Otreppe
    https://www.aircrack-ng.org

    usage: aireplay-ng <options> <replay interface>

    Filter options:

    -b bssid : MAC address, Access Point
    -d dmac : MAC address, Destination
    -s smac : MAC address, Source
    -m len : minimum packet length
    -n len : maximum packet length
    -u type : frame control, type field
    -v subt : frame control, subtype field
    -t tods : frame control, To DS bit
    -f fromds : frame control, From DS bit
    -w iswep : frame control, WEP bit
    -D : disable AP detection

    Replay options:

    -x nbpps : number of packets per second
    -p fctrl : set frame control word (hex)
    -a bssid : set Access Point MAC address
    -c dmac : set Destination MAC address
    -h smac : set Source MAC address
    -g value : change ring buffer size (default: 8)
    -F : choose first matching packet

    Fakeauth attack options:

    -e essid : set target AP SSID
    -o npckts : number of packets per burst (0=auto, default: 1)
    -q sec : seconds between keep-alives
    -Q : send reassociation requests
    -y prga : keystream for shared key auth
    -T n : exit after retry fake auth request n time

    Arp Replay attack options:

    -j : inject FromDS packets

    Fragmentation attack options:

    -k IP : set destination IP in fragments
    -l IP : set source IP in fragments

    Test attack options:

    -B : activates the bitrate test

    Source options:

    -i iface : capture packets from this interface
    -r file : extract packets from this pcap file

    Miscellaneous options:

    -R : disable /dev/rtc usage
    --ignore-negative-one : if the interface's channel can't be determined,
    ignore the mismatch, needed for unpatched cfg80211
    --deauth-rc rc : Deauthentication reason code [0-254] (Default: 7)

    Attack modes (numbers can still be used):

    --deauth count : deauthenticate 1 or all stations (-0)
    --fakeauth delay : fake authentication with AP (-1)
    --interactive : interactive frame selection (-2)
    --arpreplay : standard ARP-request replay (-3)
    --chopchop : decrypt/chopchop WEP packet (-4)
    --fragment : generates valid keystream (-5)
    --caffe-latte : query a client for new IVs (-6)
    --cfrag : fragments against a client (-7)
    --migmode : attacks WPA migration mode (-8)
    --test : tests injection and quality (-9)

    --help : Displays this usage screen

    No replay interface specified.
    root@ReckH:~# rfkill unblock all
    root@ReckH:~# rfkill list

    thank you for helping me, here are the ones I have
    and after what do i do ????

  6. #6
    Join Date
    2018-Oct
    Posts
    17
    hey

    Thank you very much for your help, because it's good.



    But I still have a problem because I can not recover my network name:

    root@ReckH:~# airmon-ng

    PHY Interface Driver Chipset

    null wlan0 r8188eu Realtek Semiconductor Corp. RTL8188EUS 802.11n Wireless Network Adapter

    root@ReckH:~# airmon-ng start wlan0

    Found 3 processes that could cause trouble.
    If airodump-ng, aireplay-ng or airtun-ng stops working after
    a short period of time, you may want to run 'airmon-ng check kill'

    PID Name
    459 NetworkManager
    549 wpa_supplicant
    3284 dhclient

    PHY Interface Driver Chipset

    null wlan0 r8188eu Realtek Semiconductor Corp. RTL8188EUS 802.11n Wireless Network Adapter

    root@ReckH:~# airodump-ng wlan0
    ioctl(SIOCSIWMODE) failed: Invalid argument
    ioctl(SIOCSIWMODE) failed: Invalid argument
    Error setting monitor mode on wlan0
    Failed initializing wireless card(s): wlan0
    root@ReckH:~#


    For me it is that my wifi usb keys do not put in "monitor mode" could tell me how to do it please

  7. #7
    Join Date
    2016-Dec
    Location
    Canada
    Posts
    221
    Quote Originally Posted by River23 View Post
    hey

    Thank you very much for your help, because it's good.



    But I still have a problem because I can not recover my network name:

    root@ReckH:~# airmon-ng

    PHY Interface Driver Chipset

    null wlan0 r8188eu Realtek Semiconductor Corp. RTL8188EUS 802.11n Wireless Network Adapter

    root@ReckH:~# airmon-ng start wlan0

    Found 3 processes that could cause trouble.
    If airodump-ng, aireplay-ng or airtun-ng stops working after
    a short period of time, you may want to run 'airmon-ng check kill'

    PID Name
    459 NetworkManager
    549 wpa_supplicant
    3284 dhclient

    PHY Interface Driver Chipset

    null wlan0 r8188eu Realtek Semiconductor Corp. RTL8188EUS 802.11n Wireless Network Adapter

    root@ReckH:~# airodump-ng wlan0
    ioctl(SIOCSIWMODE) failed: Invalid argument
    ioctl(SIOCSIWMODE) failed: Invalid argument
    Error setting monitor mode on wlan0
    Failed initializing wireless card(s): wlan0
    root@ReckH:~#


    For me it is that my wifi usb keys do not put in "monitor mode" could tell me how to do it please
    airmon-ng start wlan0
    easy to start; hard to finish

  8. #8
    Join Date
    2018-Oct
    Posts
    17
    Hello
    I tried to do:

    root@ReckH:~# ifconfig wlan0 down
    root@ReckH:~# iwconfig wlan0 mode monitor
    Error for wireless request "Set Mode" (8B06) :
    SET failed on device wlan0 ; Invalid argument.


    ps: It's been that since the last week-end I've changed totally from system to kali linux

  9. #9
    Join Date
    2016-Dec
    Location
    Canada
    Posts
    221
    Quote Originally Posted by River23 View Post
    Hello
    I tried to do:

    root@ReckH:~# ifconfig wlan0 down
    root@ReckH:~# iwconfig wlan0 mode monitor
    Error for wireless request "Set Mode" (8B06) :
    SET failed on device wlan0 ; Invalid argument.


    ps: It's been that since the last week-end I've changed totally from system to kali linux
    do you have a different adapter to try if you can set moniter.
    easy to start; hard to finish

  10. #10
    Join Date
    2016-Dec
    Location
    Canada
    Posts
    221
    Quote Originally Posted by bigbiz View Post
    airmon-ng start wlan0
    https://www.google.com/url?sa=t&rct=...1sk3sPXwsqO8j5


    seems your adapter is unique
    easy to start; hard to finish

  11. #11
    Join Date
    2018-Oct
    Posts
    17
    I will look at the links you gave meno I have no other, I try them or I buy them and it works very well. By cons it was under window and on the box it is linux compatible.I will look at the links you gave me

  12. #12
    Join Date
    2016-Dec
    Posts
    421
    As mentioned before and on Aircrack-ng website, kill network managers prior to putting in monitor mode.

  13. #13
    Join Date
    2018-Oct
    Posts
    17
    I'm sorry I could not answer before but I had some health problems.

  14. #14
    Join Date
    2018-Oct
    Posts
    17
    I solved the problem I changed wifi keys I took the TL-WN823N .I have the monitor mode but when I run an aireplay-ng -c ......... or it is pass nothing, or I have a "sent 64 directed DeAuth (code7). And his load indefinitely I waited more 1h. Someone could help me and tell me what is the code 7

    thank you in advance

Similar Threads

  1. Replies: 5
    Last Post: 2015-10-02, 01:56
  2. TP-Link TL-WN725N
    By owen420 in forum NetHunter General Questions
    Replies: 1
    Last Post: 2014-12-20, 05:26

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •