Wlan0 not showing up after killing it with "airmon-ng start wlan0" and then "Kill (PID)"

[Marwan]

So i used the command "airmong-ng start wlan0@ then killed the internet and after that wlan0 never showed up again no matter what i did.
i tried restarting my network manager and i tried restarting Kali Linux and nothing works, and it seems that my internet works fine since since i can access the forums...
i run Kali Linux 2020.2 on VMware 15.5 pro which i just installed yesterday so i am a complete newbie.

Network adapter: Qualcomm Atheros QCA9377 Wireless Network Adapter

here are some commands that would prob might help you. idk

ifconfig:

root@Marwan:/home/marwan# ifconfig
eth0: flags=4163<UP,BROADCAST,RUNNING,MULTICAST>  mtu 1500
        inet6 fe80::20c:29ff:fe23:5f29  prefixlen 64  scopeid 0x20<link>
        ether 00:0c:29:23:5f:29  txqueuelen 1000  (Ethernet)
        RX packets 75243  bytes 92268089 (87.9 MiB)
        RX errors 2  dropped 3  overruns 0  frame 0
        TX packets 47594  bytes 4189614 (3.9 MiB)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0
        device interrupt 19  base 0x2000  

lo: flags=73<UP,LOOPBACK,RUNNING>  mtu 65536
        inet 127.0.0.1  netmask 255.0.0.0
        inet6 ::1  prefixlen 128  scopeid 0x10<host>
        loop  txqueuelen 1000  (Local Loopback)
        RX packets 16  bytes 796 (796.0 B)
        RX errors 0  dropped 0  overruns 0  frame 0
        TX packets 16  bytes 796 (796.0 B)
        TX errors 0  dropped 0 overruns 0  carrier 0  collisions 0

iwconfig:

root@Marwan:/home/marwan# iwconfig
lo        no wireless extensions.

eth0      no wireless extensions.

Network connectivity "ping google.com -c 4; traceroute google.com; curl ifconfig.me"

root@Marwan:/home/marwan# ping google.com -c 4; traceroute google.com; curl ifconfig.me
PING google.com (172.217.169.206) 56(84) bytes of data.
64 bytes from sof02s34-in-f14.1e100.net (172.217.169.206): icmp_seq=1 ttl=128 time=110 ms
64 bytes from sof02s34-in-f14.1e100.net (172.217.169.206): icmp_seq=2 ttl=128 time=108 ms
64 bytes from sof02s34-in-f14.1e100.net (172.217.169.206): icmp_seq=3 ttl=128 time=89.9 ms
64 bytes from sof02s34-in-f14.1e100.net (172.217.169.206): icmp_seq=4 ttl=128 time=88.6 ms

--- google.com ping statistics ---
4 packets transmitted, 4 received, 0% packet loss, time 3011ms
rtt min/avg/max/mdev = 88.611/99.074/109.668/9.851 ms
traceroute to google.com (172.217.169.206), 30 hops max, 60 byte packets
 1  192.168.190.2 (192.168.190.2)  0.343 ms  0.708 ms  0.341 ms

ifconfig wlan0 up

root@Marwan:/home/marwan# ifconfig wlan0 up
wlan0: ERROR while getting interface flags: No such device

Gateaway "route -n":

root@Marwan:/home/marwan# route -n
Kernel IP routing table
Destination         Gateway              Genmask             Flags        Metric  Ref    Use Iface
0.0.0.0               192.168.190.2       0.0.0.0                  UG           100      0        0 eth0
192.168.190.0     0.0.0.0                 255.255.255.0        U             100      0        0 eth0

so what i was trying to do is to hack an internet and i was following a guide and seems that i failed hard for my 1st hack ever any idea how to make wlan0 show up again after killing it

[dustednoob]

as i know You have to kill the pid(s) first. perhaps thats what goes wrong ? only a suggestion
I had the same wifi card as pci card before i changed over to a dual band USB adapter.
worked pretty good.

1)
airmon-ng check kill

2)
airmon-ng start wlan0

on my other wifi adapter (USB) it works little different: and there i don't have the wlan0mon - i have the wlan0 (but everything works fine as it should)

ifconfig wlan0 down
airmon-ng check kill
iwconfig wlan0 mode monitor
ifconfig wlan0 up
airmon-ng start wlan0 (to check if the wlan0 is already in monitor mode), can skip this step

what I recognized using my USB wifi adapter and ethernet adapter together, while the ethernet was in use,
the system often shut down my USB adapter - but that should not be an issue with a pci wifi card i think.