airmon-ng output
If i kill Networkmanager i also cannot see the wlan stick in ifconfig.
If i activate Networkmanager again, and try monitor ( obviously ) i got problems, like ERROR adding monitor mode interface: command failed: Invalid argument (-22)
Code:
Code:
root@kali:~# NetworkManager
root@kali:~# airmon-ng start wlx00c0ca82fdfa
Found 3 processes that could cause trouble.
If airodump-ng, aireplay-ng or airtun-ng stops working after
a short period of time, you may want to kill (some of) them!
PID Name
2728 NetworkManager
2732 wpa_supplicant
2734 dhclient
PHY Interface Driver Chipset
phy0 wlx00c0ca82fdfa rtl8187 Realtek Semiconductor Corp. RTL8187
ERROR adding monitor mode interface: command failed: Invalid argument (-22)
root@kali:~#
Code:
root@kali:~# airmon-ng check kill
Killing these processes:
PID Name
1351 wpa_supplicant
root@kali:~# kill 1351
bash: kill: (1351) - No such process
root@kali:~# airmon-ng
PHY Interface Driver Chipset
phy0 wlx00c0ca82fdfa rtl8187 Realtek Semiconductor Corp. RTL8187
root@kali:~# airmon-ng start wlx00c0c0ca82fdfa
PHY Interface Driver Chipset
phy0 wlx00c0ca82fdfa rtl8187 Realtek Semiconductor Corp. RTL8187
root@kali:~#
x
I can connect to my home WLAN. So why is the name so strange? This is my second card, i used first TPLink722n, and if i plug this one in, everything works fine, interface name is wlan0 etc. so how it should be.
After plug in
Code:
1913.351192] r8169 0000:09:00.0 eth0: link down
[ 1947.646271] usb 1-2: USB disconnect, device number 9
[ 1948.734660] usb 1-2: new high-speed USB device number 10 using xhci_hcd
[ 1948.869076] usb 1-2: New USB device found, idVendor=0bda, idProduct=8187
[ 1948.869082] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1948.869086] usb 1-2: Product: RTL8187_Wireless
[ 1948.869090] usb 1-2: Manufacturer: Manufacturer_Realtek_RTL8187_
[ 1948.869092] usb 1-2: SerialNumber: 00C0CA82FDFA
[ 1948.984424] ieee80211 phy3: Selected rate control algorithm 'minstrel_ht'
[ 1948.984834] ieee80211 phy3: hwaddr 00:c0:ca:82:fd:fa, RTL8187vB (default) V1 + rtl8225z2, rfkill mask 2
[ 1948.993693] rtl8187: Customer ID is 0xFF
[ 1948.994093] rtl8187: wireless switch is on
[ 1948.999417] rtl8187 1-2:1.0 wlx00c0ca82fdfa: renamed from wlan0
[ 1949.028958] IPv6: ADDRCONF(NETDEV_UP): wlx00c0ca82fdfa: link is not ready
[ 1950.859188] IPv6: ADDRCONF(NETDEV_UP): wlx00c0ca82fdfa: link is not ready
[ 1950.908624] IPv6: ADDRCONF(NETDEV_UP): wlx00c0ca82fdfa: link is not ready